Parts for Ge GDE25ESKJRSS: Fresh Food Section Parts

This air tower assembly directs and channels cold air inside the fresh-food compartment to help maintain even cooling and proper airflow. It replaces a damaged or cracked duct that can cause uneven temperatures. What it does

• Routes conditioned air from the evaporator into the fresh-food section for consistent cooling.
• Helps prevent warm spots and reduces localized thawing or food spoilage.
• Restores proper airflow if existing tower is cracked, broken, or blocked.
• Can reduce frost build-up caused by disrupted airflow pathways.

• Disconnect power before starting any service to avoid electrical shock.
• Remove interior shelves and panels as needed for access; handle plastic parts gently to avoid cracking.
• Inspect surrounding seals and ducts during replacement; secure with factory fasteners only.

This replacement air tower assembly is the vertical duct that channels chilled air through the refrigerator compartment. Replacing a damaged tower restores proper airflow to help maintain even temperatures and consistent cooling from top to bottom.

• Directs cold air from the evaporator to vents in the fresh food section
• Helps balance temperatures and reduce warm spots
• Often replaced when the original is cracked, broken, or warped
• Common symptoms: weak airflow from refrigerator vents and uneven cooling in the fresh food compartment

• Disconnect power to the refrigerator before servicing.
• Remove shelves and bins for access; release tabs or remove screws securing the old tower.
• Transfer any clips or sensors from the original, if present; seat and secure the new tower.
• Restore power and verify airflow from the vents.

The Bypass Filter Plug is an OEM part for GE refrigerators. It is used when a water filter is not installed. The bypass plug is essential for maintaining the refrigerator's water flow system, allowing water to bypass the filtration process. This is particularly useful during times when a replacement water filter is not immediately available or in situations where the household water supply is already adequately purified and additional filtration is not necessary.

Common causes of issues with the bypass filter plug include physical damage from handling, wear and tear over time, or improper installation. A faulty bypass filter plug can disrupt the water flow and affect the performance of the water dispenser and ice maker.

Symptoms of a bad Bypass Filter Plug include:

• Leakage or dripping from the water dispenser area.
• Difficulty in installing or removing the plug from the filter housing.
• Decreased water flow rate through the dispenser, indicating a potential blockage or improper fit.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Manifold & Housing are OEM components specifically designed for GE refrigerators. This part includes both the manifold which distributes water and the outer housing that protects it. 

The manifold & housing work together to deliver filtered water to the refrigerator's dispenser and ice maker. It is responsible for efficiently directing water flow and ensuring reliable operation of components that require water. 

Symptoms of a bad manifold & housing include:

• Low water pressure at the dispenser 
• Streaking or staining around water line connections
• Ice maker or dispenser malfunctions due to lack of water
• Dripping or leaks from manifold or housing areas

This OEM GE part is specifically designed to fit your model fridge. It is also compatible with Hotpoint, RCA, and some Kenmore models for a factory fit and like-new performance.
 

The GE XWFE Refrigeration Water Filter is an OEM part for GE refrigerators. This advanced water filter is designed to reduce a wide range of contaminants, including chlorine, lead, cysts, and select pharmaceuticals, providing clean and safe drinking water and ice. It seamlessly integrates into the refrigerator's filtration system, ensuring optimal water quality.

You should replace this water filter if it becomes clogged or reaches the end of its lifespan, typically every six months. Common causes of a bad water filter include excessive contaminants, improper installation, or failure to follow the replacement schedule.

Symptoms of a bad water filter include:

• Reduced water flow from the dispenser
• Unpleasant taste or odor in water and ice
• Cloudy or discolored water
• The filter indicator light on the refrigerator signaling a replacement

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Temperature Sensor is an OEM replacement part for GE refrigerators, designed to accurately monitor and relay the temperature inside the refrigerator and freezer compartments to the electronic control board. By detecting the slightest changes in internal temperature, the sensor allows the control board to make real-time adjustments to the cooling system, activating the compressor and fans as needed to maintain optimal conditions for food preservation.

Over time, the temperature sensor can fail due to electrical issues, exposure to moisture, or general wear and tear. A malfunctioning sensor can lead to improper temperature regulation, affecting the efficiency of the refrigerator and the freshness of stored food.

Symptoms of a bad Temperature Sensor include:

• The refrigerator or freezer not maintaining the set temperature 
• The appliance running continuously or more frequently than normal
• Inaccurate temperature readings displayed  

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This top LED cover is the replacement light lens that protects and diffuses the refrigerator's top LED assembly for even interior lighting and a finished look. Replaces a cracked, yellowed, or missing lens to restore light distribution. What it does:

• Protects the LED module from dust, moisture, and impacts
• Diffuses and softens LED output for even interior illumination
• Prevents glare and visible hot spots from exposed LEDs
• Helps maintain a clean, finished appearance inside the appliance
• Can address symptoms like uneven lighting, visible LED bulbs, or a cracked/warped lens

• Disconnect power to the appliance before starting any work.
• Handle the lens gently to avoid scratching or cracking; wear gloves if needed.
• Removal/installation typically involves releasing retaining clips or removing a few screws—retain fasteners for reuse.
• Align the cover over the LED assembly and secure until it snaps or fasteners are tightened; test lighting after restoring power.