Parts for Briggs & Stratton 121P02-0002-F1: Gasket Sets - Engine & Valve Parts

This oil seal is a common part engineered to work in engines that power generators, vacuum cleaners, snowblowers, leaf blowers, mowers, and other small engine applications. The seal sits between the crankcase and the crankshaft. It is designed as a barrier to prevent oil leakage and to stop contaminants from leaving the crankcase. When the gasoline engine exhibits diminished power, and especially if it begins to emit oily gray or bluish smoke, there is a good chance the oil seal needs to be replaced. In order to replace the faulty seal, begin by removing the starter housing and taking off the nut that holds the starter wheel to the main shaft. The user will find the old seal on this shaft. Remove it and install the new seal, pushing it into place with the edges of a socket, then tapping it securely into place with a hammer. When choosing a replacement seal, remember to use an OEM genuine replacement part that is guaranteed to match the specs for the original part. This will ensure a quality match and long replacement life. This seal is compatible with Toro, Lawn-Boy, and Briggs & Stratton engines.

This genuine replacement crankcase gasket creates an airtight seal on the crankcase so that oil and air do not leak out of the engine when it is running. Over time, this gasket is exposed to extreme pressure and high heat and will naturally deteriorate. It could become faulty and create leaks or it could break entirely. In either case, a full replacement of the gasket is the only solution. This OEM part can provide an exact fit for compatible lawn and garden equipment engines. This genuine crankcase gasket is manufactured to strict standards by Briggs & Stratton and is compatible with select engines on lawn mowers and generators from Briggs & Stratton, Lawn Boy, and Toro. This gasket is made of durable composite material and it is sold as an individual unit. Other gaskets, hardware, or related parts are all sold separately. The repair can be done with just a wrench, but be sure to allow the engine to cool entirely before beginning any repairs. Always wear gloves and disengage the spark plug for safety when performing engine work.

This authentic replacement oil seal is for use with a range of small engines. The oil seal is the lower seal that is located in the engine's sump. The seal is made to ensure that there are no oil leaks that could cause issues with the performance of the engine. If the seal is not working properly, it could result in leaks, and the machine may not have enough oil to function properly. Lack of oil can also cause serious issues with the engine. The oil seal is prone to wearing out over time. The seal can become worn and it can start to deteriorate the longer it is used. Owners should make it a point to replace the oil seals whenever they are changing their oil, oil filter, and gaskets. The oil seal is a genuine OEM replacement part, and it is sold individually. The oil seal is compatible with more than 150 different models of machine. This includes models of lawnmower, snowblowers, pressure washer, leaf blowers, generator, wood chipper, and other small engines. Compatible brands include Briggs & Stratton, Craftsman, Toro, Lawn-Boy, and Simplicity.

The flywheel key is the component on outdoor equipment that keeps the flywheel connected to the crankshaft. Over time, this key may become damaged or broken, particularly if the engine experiences a forceful stop, like hitting a large stationary object. If the flywheel key breaks, the engine will not start. A slightly damaged flywheel key is noticeable through symptoms like misfiring, backfiring, or having no power. If any of these are occurring, the flywheel key should be replaced to prevent complete engine failure.A flywheel puller tool is required for this repair. Make sure the engine is cool before working on the flywheel. Wear safety gear, including gloves and eye protection. Disconnect the spark plug and remove the blower housing. Remove the flywheel mounting nut and set it aside. Take the recoil starter cup off the mower. Use the flywheel puller to remove the flywheel and access the flywheel key. Remove the broken flywheel and replace it with the new flywheel. Reverse the steps to put the mower back together.This flywheel key is made of an aluminum alloy and is sold as an individual part. It is designed for use in lawnmowers, lawn tractors, and other small engines manufactured by Briggs and Stratton, Toro, Lawn-Boy, Simplicity, MTD, and others.

This screw is a genuine Midwest Engine replacement part for small engine appliances, including lawn tractors, lawn mowers, snowblowers, leaf blowers, vacuums, and tillers. The purpose of a screw is to tightly link materials together through rotation that pierces into the material. A screw might have to be replaced in the event that it is lost or misplaced, a common occurrence due to its size. A screw might also be replaced if it deteriorates over time, through erosion, cracking, or piercing, thereby reducing its efficacy in holding materials together. This kind of damage can be attributed to general overuse, to age, or simply to long-term exposure. If a screw is subject to any of this kind of damage, it is best to replace it immediately, as the materials held together by the screw must continue to be held together. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This screw is compatible with the following brands: Briggs & Stratton, Toro, Cub Cadet, and Lawn Boy.

This valve retainer is an authentic replacement part for use with many types of small lawn and garden engines. The retainer valve helps to keep the lock valve spring on the valve. It is shaped similarly to a washer, which will fit over the top of the valve spring. The piece also helps to add space between the valve spring and the head of the valve. The valve retainer is made from metal, and it is a small piece. The retainer could become lost and need replacement when performing other maintenance on the engine's valves. The metal could also become corroded or break. In those cases, it will need to be replaced as soon as possible. This is a genuine OEM replacement part that is sold individually. The part can be used with many types of equipment including lawn mowers, snowblowers, tillers, pressure washers, edgers, leaf blowers, log splitters, and wood chippers. Compatible brands include Briggs & Stratton, Craftsman, Toro, Cub Cadet, Murray, Lawn-Boy, Snapper, MTD, Simplicity.

This grip-starter rope is a genuine Midwest Engine replacement part for outdoor appliances with small pull start engines, such as lawn mowers, snowblowers, wood-chippers, leaf blowers, and chainsaws. The grip-starter rope is the piece that allows an appliance user to start the engine by pulling the rope; this mechanism can be referred to as a recoil starter, a starter rewind, or a rope start as well. Any damage to a grip-starter rope will be obvious to the naked eye; while the problems with the actual starting mechanism of a pull start-operated engine might be more difficult to assess and root out, the damage to the actual grip-starter rope itself will come in the form of tears, rips, and general time-worn erosion of the casing material of the rope. If there is significant tearing on the rope itself, this replacement grip-starter rope can serve as a replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This grip-starter rope is compatible with the following brands: Briggs and Stratton, Toro, Cub Cadet, and Simplicity.

This kit-needle/seat is also called a float needle. It is a genuine Midwest Engine part. It is a replacement part for various makes and models of small engine machinery, such as lawn mowers, edgers, and more. On these machines, float needles have ears or tabs on the ends that help stop leaks while letting gas in, especially in the carburetor.A faulty, damaged, or broken float needle may be responsible for leaks, especially small leaks when the engine runs. If the machine is leaking, the float needles should be checked. Before making any repairs, be sure to allow the engine to properly cool, empty the fuel tank, and disconnect the spark plug to prevent the engine from accidentally powering on.This gear is a genuine OEM part that is sourced directly from the manufacturer. It is sold individually. It is made to be compatible with equipment with small engines manufactured by Briggs and Stratton.

This part is a replacement float bowl gasket. This is a genuine OEM part made by Midwest Engine and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a snapped, worn, or otherwise defective float bowl gasket in various engines. This float bowl gasket seals the gap between the float bowl and the carburetor, which helps to prevent fuel from leaking. Gaskets are particularly subject to wear and tear, and over time will become weathered, brittle, or otherwise deteriorated, thus requiring replacement. If you notice fuel leaking from the engine, this gasket may need to be replaced. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this float bowl gasket, the appropriate owner's manual and equipment diagrams should be referred to. This float bowl gasket is a genuine OEM part made of durable materials and is sold individually. It is suitable for use with small engines that have been manufactured by Midwest Engine and Briggs and Stratton.

This is a fuel line replacement intended to keep a lawnmower's engine running smoothly. It is long enough to make a couple of fuel lines, just cut the fuel line to the desired length and keep the rest as a spare. When a mower doesn't start easily or performs poorly when running, the fuel delivery system may have a problem and will need repair. The fuel line that supplies gas from the tank to the carburetor may be cracked or broken. When this occurs, it is best to replace the fuel line before it becomes a flammable hazard. This is an OEM replacement fuel line sourced from the manufacturer and is sold individually. This replacement part is compatible with different Briggs & Stratton mowers. Remember to use work gloves and drain the gas tank before the installation of this part.

This sealing washer is a genuine Midwest Engine part, sold individually. This sealing washer can be used as a replacement part for a variety of small engine outdoor appliances including chipper shredders, lawn mowers, and tillers. The purpose of a sealing washer is to create space between fastening components so they are not damaged by friction.The sealing washer of an outdoor appliance might have to be replaced if it is lost, misplaced, or damaged to the point that it cannot serve its function. The sealing washer could be stripped over time from general wear and tear or, as it is a small part, can be lost or misplaced easily. If this occurs, the component should be replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This sealing washer is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, and Cub Cadet.

This genuine rocker switch is designed as an identical replacement part for select models of blower/vacuum units. The rocker switch is also known as a power switch or on/off switch and it is what controls the current to electric blowers. The switch is made of plastic and metal. This switch may become worn and not function well after regular use because of the repetitive motion of turning the machine on and off. In some cases, the switch may experience electrical malfunctions that could present a fire hazard or keep the unit from working at all. In the event that the switch is damaged or defective, it will need to be replaced. This genuine OEM replacement rocker switch is manufactured by Briggs & Stratton. It can be used with more than 150 models of machines from Briggs & Stratton, Toro, and Vanguard. This part is made of durable plastic and metal components and is sold as an individual unit. It plugs into the pressure washer via wires, but a screwdriver may be needed to assist in the installation. Always disconnect the power supply when working on electrical components and wear gloves for safety.

A spark plug boot is an important piece of rubber hardware. The purpose of the spark plug boot is to connect the spark plug to the magneto. It is designed for use with pieces of outdoor lawn and garden power equipment that have small engines, such as lawn mowers, snow blowers, tillers, pressure washers, leaf blowers, generators, and wood chippers. It is compatible with products by brands such as Briggs & Stratton, Toro, Cub Cadet, Snapper, and Simplicity.The spark plug boot part is important to outdoor equipment with small engines because it safely connects the ignition coil to the spark plug. Naturally over time, and with the wear and tear from use, the rubber material on the spark plug boot may dry out, crack, and fail, and will require replacement. Luckily, the replacement or repair process of the spark plug boot should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.This spark plug boot is made out of rubber. This spark plug boot is an original OEM part sourced directly from the manufacturer, Midwest Engine. It is sold individually.

This replacement part is a muffler and is intended for use in different types of equipment. This is a genuine replacement part made by Midwest Engines. A muffler is a device that is typically attached to different kinds of machinery. This part is able to dampen any noise that comes from the device so that the user is able to complete a task without being overcome by loud noises. A new muffler might be needed if the current one is damaged or misplaced. The user might know when a new muffler is needed as typically the engines make lots of noise when a muffler is not attached. Be sure that the machine is completely off before attempting a repair, and also reference the specific user guide for further directions on replacements. Note that this part is sold individually and is compatible with different types of equipment. This part is a genuine OEM replacement part.

This fuel tank cap was created for easy installation. It is made of durable and chemical-resistant materials, with clear indicators of the types of fuel that can be used in conjunction with this replacement cap. No tools should be needed for installation as this part clips into position and is a secure cap to prevent misplacement. Fixed to the machine with the appropriate hardware, this OEM replacement part will create an airtight seal on a wide variety of garden and home equipment, including a wide array of Briggs & Stratton machines or fuel tanks. This part ships individually and will not come with the fuel tank.

This replacement part is a float bowl. This part is a small part of the carburetor and is able to hold a small amount of liquid gasoline. This serves as a reservoir for fuel.If the engine is unable to run due to lack of fuel, it might be because of a malfunctioning float bowl. Be sure to wear work gloves during this repair as working near the carburetor might be dangerous in certain situations. This is a genuine replacement part made by Midwest Engine. It is an OEM replacement part which will ensure a proper fit. This part is sold individually.