General Electric Gasket & Seal

This surface burner gasket seals the burner assembly to the cooktop. Replacing a worn gasket restores a tight seal to help support reliable ignition, a stable flame, and keeps spills and moisture from entering the burner well. What it does:

• Seals between the surface burner assembly and cooktop
• Helps maintain proper airflow for consistent ignition and flame
• Helps prevent liquids, crumbs, and grease from seeping below the burner
• Common symptoms of failure: distorted or hardened gasket, visible cracks, uneven/weak flame, or persistent clicking during ignition

• 1 gasket

• Disconnect power and shut off gas supply; allow the appliance to cool completely
• Remove grate, burner cap, and burner head to access the gasket
• Clean mating surfaces; seat the gasket flat and do not use sealants or adhesives unless specified by the manufacturer
• Reassemble, restore gas, and verify burner operation; leak-check with soapy water if any gas fittings were disturbed

This gasket seals the upper oven door to the front frame to keep heat inside the cavity for stable baking and safer, more efficient operation. Replace a worn seal to stop heat leaks and improve temperature consistency.

• Provides a heat-resistant seal around the upper oven door perimeter
• Helps the oven preheat faster and hold the set temperature
• Reduces heat and steam escaping at the door edges
• Common signs of wear: fraying or tears, flattened/hardened sections, visible gaps, longer preheat or uneven baking

• Disconnect power and allow the oven to cool completely before starting.
• Open the door and carefully pull the old gasket from the retainers around the frame.
• Press the new gasket evenly into the retainers without stretching; align corners and ensure the ends meet cleanly.
• Close the door to confirm uniform contact around the seal before heating.

Replacement refrigerator door gasket for the fresh food compartment. It forms a tight seal around the door to keep cold air in and humidity out—restoring stable temperatures, reducing condensation, and improving cooling efficiency when the old gasket is worn.

• Creates an airtight seal between the fresh food door and cabinet to prevent air leaks
• Helps maintain consistent refrigerator temperatures and proper humidity
• Reduces condensation and frost around the door perimeter
• Replaces gaskets that are torn, deformed, or no longer sealing evenly

• Disconnect power to the refrigerator before starting.
• Remove the old gasket and clean the door/liner sealing surfaces and retainer channel.
• Condition the new gasket in warm water or with low heat to relax folds; do not overheat.
• Press the gasket fully into the retainer (start at corners), then close the door and check for uniform contact; warm and reshape as needed for a complete seal.

The lower gasket shield is a guide that protects the refrigerator door gasket at the bottom edge, helping the door close smoothly and maintain an even, reliable seal to keep temperatures stable and moisture down. What it does:

• Protects the lower edge of the door gasket from wear and deformation
• Guides the gasket into place for a snug, even seal
• Helps reduce warm-air leaks that can cause condensation or frost
• Replaces cracked, missing, or warped shields that can lead to poor sealing

• Includes 1 lower gasket shield

• Disconnect power and open the door for safe access
• Remove any lower door bins if needed
• Gently pull back the gasket at the lower edge to expose the shield and fasteners
• Install the new shield, reseat the gasket fully, and verify the seal with a paper-slip test

This freezer door gasket forms an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or damaged seal helps restore proper temperature, reduce frost, and improve energy efficiency.

• Seals the freezer door perimeter to maintain set temperature and airflow
• Helps reduce frost/ice buildup and condensation around the door opening
• May help if you notice warm spots, frequent frost, the door not staying shut, or visible gasket tears/gaps
• Reduces warm air infiltration that can cause long run times and temperature swings

• Unplug the refrigerator before servicing
• Warm the new gasket in hot tap water or with a hair dryer on low to make it pliable; seat the corners first
• Depending on the model, either press the gasket into the retainer channel or loosen and retighten inner-liner screws to secure—do not overtighten
• After installation, check the seal all around (dollar-bill test); gently warm and reshape any areas with gaps

This oven light gasket seals the light lens/cover to the oven cavity. Replacing a worn gasket restores a tight barrier that helps keep heat, steam, and splatter away from the light assembly and lets the lens seat securely.

• Creates a heat-resistant seal between the light lens/cover and oven liner
• Helps keep moisture, grease, and food vapor out of the light assembly
• Supports proper seating of the lens cover to prevent looseness or rattling
• Common signs: cracked/brittle or missing gasket, visible gaps around the lens, condensation or residue behind the lens, lens cover that won't stay tight

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks for access; open/remove the light lens cover as directed in the manual
• Carefully remove the old gasket and any residue; clean the sealing surface
• Fit the new gasket evenly around the lens/fixture and reinstall the lens cover; restore power and test

This felt seal creates a smooth, airtight barrier where the drum meets the bulkhead in your dryer. Replacing a worn seal helps maintain proper airflow, protect fabrics from snagging, and reduce scraping or squealing noises during operation. What it does:

• Seals the gap between the rotating drum and front/rear bulkhead to contain heat and airflow
• Provides a low-friction, cushioned surface for the drum rim
• Helps keep lint and debris out of the cabinet
• Common symptoms of failure: longer or uneven dry times, rubbing/scraping noises, clothes catching or leaving marks at the drum edge, visibly worn or torn felt

• 1 felt seal

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the top/front panel to access the drum and bulkhead; support drum as needed
• Remove old felt and adhesive; clean the mating surface thoroughly
• Dry-fit the new seal; install per manufacturer guidance; allow proper set time before reassembly
• Hand-rotate the drum to verify even contact and clearance, then test operation

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This is a gasket made for use with washing machines. This particular gasket fits between the washer tub and the door, forming a seal that prevents leaks. Over time, gaskets are subject to wear and tear that can cause them to become brittle, rip, tear, warp, or otherwise be rendered ineffective. If the user notices that there is water leaking from the washing machine door during use, or the gasket is displaying visible signs of wear and tear, replace this part immediately. No tools are required to install this gasket.This gasket is manufactured from high-quality, durable, non-corrosive materials to ensure the best possible quality. This part is manufactured by General Electric and has been sourced directly from the manufacturer. It is sold individually and compatible with washers from General Electric, Hotpoint, and RCA.

This small donut-shaped gasket fits where specified in your refrigerator's parts diagram to create a tight seal between mating components. Replacing a worn gasket helps stop minor leaks and restore a secure fit.

• Forms a tight seal at the designated joint or fitting
• Helps prevent seepage or drips from a compromised connection
• Replaces a brittle, cracked, flattened, or missing original gasket
• Supports proper assembly alignment and a snug fit

• Unplug the refrigerator and, if servicing the water system, shut off the water supply
• Note the gasket's original placement and orientation before removal
• Clean mating surfaces; lightly moisten the new gasket to ease seating
• Reassemble without overtightening; restore power/water and check for leaks

This fresh food door gasket creates an airtight seal around the refrigerator compartment door to prevent air leaks. Replacing a worn seal helps maintain stable temperatures, reduce moisture at the door, and restore proper closing and sealing.

• Creates a tight seal around the fresh food door to prevent air infiltration
• Helps maintain consistent temperatures and minimize condensation at the door
• Wear indicators include cracks, tears, warping, or visible gaps in the seal
• Common symptoms: door not sealing well, warm spots in the fridge, or longer run times

• Disconnect power before servicing
• Remove the old gasket and clean the door's gasket channel/retainer
• Warm the new gasket in clean warm water to relax folds; start at corners and press the lip fully into the channel without stretching
• Close the door and check for uniform contact; adjust hinges/strike if needed and allow up to 24 hours for the gasket to fully conform

This is the door pad. Consider replacing both when replacing trim number WB07T10230

This refrigerator French door gasket restores a tight seal around the door opening. Replacing a worn or damaged gasket helps keep cold air in and humid air out to maintain stable temperatures and reduce condensation. What it does:

• Forms an airtight seal between the door and the cabinet on French-door models
• Helps prevent warm air leaks, moisture buildup, and frost around the door opening
• Replace if torn, warped, cracked, or if gaps remain when the door is closed
• Common signs include condensation on or around the gasket and the door not sealing fully

• 1 door gasket

• Unplug the refrigerator and remove items from the door bins
• Warm and relax the new gasket (soak in warm water or use low heat) to remove kinks; do not overheat
• Lift the old gasket out of the retainer; if your model uses retainer screws, loosen them, swap the gasket, then re-tighten
• Press the new gasket fully into the channel, ensure corners seat, then close the door and check for an even seal all around

This fresh food door gasket restores a tight seal around the refrigerator compartment on bottom-freezer models. Replacing a worn seal helps keep cold air in, reduce condensation, and maintain stable temperatures and efficiency.

• Seals the perimeter of the fresh food door to prevent air leaks
• Helps maintain proper temperature and humidity inside the refrigerator
• Common signs of failure: tears, warping, gaps, condensation at the door, warm spots, or longer run times
• Can improve door closing and overall cooling performance when the old gasket is damaged

• Unplug the refrigerator before service
• Warm the new gasket in hot tap water to relax and improve flexibility
• Seat the gasket fully into the door channel; on some models you may need to loosen and re-tighten retainer screws
• Use low heat (hair dryer) to smooth waves after install and check for a uniform seal all around

This replacement freezer door gasket creates a secure, flexible seal around the freezer door to help keep cold air in and warm air out, restoring proper door closure and helping the freezer maintain consistent temperature. What it does:

• Forms an airtight seal around the freezer door to reduce air leaks.
• Helps prevent frost and ice buildup inside the freezer.
• Restores proper door closure so the freezer maintains temperature more reliably.
• Reduces excess compressor cycling associated with a worn or damaged seal.

• Disconnect power or turn the appliance off before starting to avoid electrical hazards.
• Remove the old gasket and clean the door flange and mounting channel before installing the new seal.
• Press the new gasket fully into the channel, working around the door to ensure even seating and full contact.
• If the gasket feels stiff, follow OEM guidance or warm it gently to help it flex; avoid high heat that can damage the seal.

This control knob seal fits around the control shaft opening on your range or cooktop to close the gap under the knob. It helps block spills and debris from entering the control area and keeps the console looking clean and finished.

• Forms a barrier between the knob/valve shaft and the control surface
• Helps prevent liquids, crumbs, and grease from seeping into the control cavity
• Restores a tidy appearance; replaces cracked, shrunken, or missing seals
• Typical signs of wear: visible damage, gaps around the knob, or residue appearing beneath the panel after spills

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool
• Pull the knob straight off the shaft and remove the old seal
• Clean the area; seat the new seal flat around the shaft—avoid side pressure on the valve stem
• Reinstall the knob and verify smooth operation and proper seal seating