General Electric Gasket & Seal

This door gasket creates an airtight seal around the perimeter of the refrigerator or freezer door. Replacing a worn seal helps maintain stable temperatures, reduce frost and moisture, and improve efficiency and food preservation.

• Seals the door opening to prevent warm air leaks and cold air loss
• Helps maintain proper temperatures in the fresh food or freezer section
• Reduces frost buildup and condensation around the door
• Replaces gaskets that are cracked, warped, torn, or won't lay flat
• Symptoms include visible gaps, moisture on or around the gasket, frequent frost, or longer run times

• Disconnect power and clear items from the door for easier access
• Warm the new gasket with a hair dryer on low or soak in warm water to relax folds
• Remove the old gasket from the retainer; press the new gasket fully into the channel, starting at the top corners and working around
• Check door alignment and sealing all around; adjust hinges if needed and perform a dollar-bill test

This gasket trim seals the dishwasher door opening, helping contain moisture and steam during cycles. Replacing a worn, torn, or missing trim restores a proper barrier and helps prevent drips or condensation at the door area. What it does:

• Provides a moisture/steam barrier where the door meets the tub opening
• Helps protect the console and surrounding surfaces from escaping steam
• Cushions the door for a snug, secure close
• Common signs to replace: cracked, flattened, deformed, or missing trim; moisture around the door edges; visible wear

• 1 gasket trim

• Disconnect power and turn off the water supply before servicing
• Open the door and pull the old trim straight out of the channel
• Clean the groove; press the new trim fully into the channel without stretching
• Open and close the door to confirm even contact; reseat if needed

The Pan Cover Front Gasket is an OEM part for GE refrigerators. This gasket provides a seal for the front edge of the refrigerator's crisper or pantry drawer pan cover, preventing cold air from escaping and ensuring that the contents remain at the optimal temperature for freshness.

Common causes of a bad gasket include regular wear and tear, exposure to food spills, or accidental damage from frequent opening and closing of the drawer.  

Symptoms of a bad pan cover front gasket include:

• The drawer not sealing properly, leading to temperature fluctuations
• Visible cracks, tears, or warping of the gasket
• Increased condensation or frost buildup in the drawer area
• Food items spoiling faster than usual

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: The part is approximately 3" in diameter.

Restore a reliable door seal with this refrigerator door gasket. It forms an airtight barrier between the door and cabinet to keep cold air in, reduce frost and condensation, and help your unit maintain stable temperatures.

• Seals the full door perimeter to prevent warm, humid air from entering the compartment
• Helps maintain consistent cooling performance and moisture control
• A worn, torn, or deformed gasket may cause temperature swings, frost/ice buildup, or moisture around the door
• Visible gaps, a door that won't stay closed, or a failed "paper test" indicate a failed seal

• Unplug the appliance before starting
• Let the new gasket relax flat; gently warm with a hair dryer on low or place in warm water to remove kinks
• Fully seat the gasket lip into the door channel/retainer, working evenly around all four sides and corners
• After installation, check the seal with a paper strip and fine-tune by gently warming and reshaping as needed

This silicone gasket creates a flexible, heat-resistant seal in range and oven assemblies. Replacing a deteriorated seal helps contain heat and moisture at joints and trim areas, protecting internal components and restoring proper fitment.

• Forms a durable, high-temperature seal between designated mating surfaces
• Helps prevent heat, steam, odors, and spills from escaping at seams
• Can help address visible gaps, leaks at edges, or looseness around trim/panels
• Restores the manufacturer-specified seal after service on affected components

• Disconnect power and allow the appliance to cool; turn off gas if applicable
• Remove old gasket/sealant and clean surfaces thoroughly; dry completely
• Position/install exactly as directed for your model; avoid stretching or over-compressing
• Follow model/service instructions for any required cure or set time before heating

The French Door Gasket is an OEM part for GE refrigerators. This gasket is designed to create a tight seal around the refrigerator's French doors, helping to maintain the internal temperature and ensuring energy efficiency. The gasket measures approximately 26 inches wide by 38 inches long.

Common causes of a bad gasket include wear and tear from regular opening and closing, exposure to temperature fluctuations, and accumulation of dirt or food particles that prevent a proper seal.

Symptoms of a bad French door gasket include:

• Visible cracks or tears in the gasket
• Condensation or frost buildup inside the refrigerator
• Increased energy consumption due to the refrigerator working harder to maintain temperature
• Difficulty closing the refrigerator doors properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Restore a tight seal and stable temperatures with this refrigerator door gasket. Replacing a worn gasket helps keep cold air in and humid air out to reduce frost, condensation, and unnecessary energy use.

• Forms an airtight seal around the door perimeter
• Helps maintain consistent temperature and humidity
• Reduces frost/ice buildup and interior condensation
• Can address doors that won't close fully or pop open
• Replace if torn, brittle, warped, or not sealing evenly

• Disconnect power before servicing
• Let the gasket warm to room temperature; use warm water or low heat to relax folds
• Remove the old gasket and press the new gasket into the retainer, seating corners first
• Check for even contact all around; adjust door/hinges as needed for a proper seal

This vent pad cushions and seals the dishwasher's door vent, helping route steam out of the tub while protecting the inner door and control area from moisture. Replacing a worn pad can help stop vent leaks and rattling.

• Creates a seal between the vent assembly and inner door liner to contain moisture
• Helps channel humid air during drying and reduces steam escaping at the vent opening
• Cushions the vent assembly to minimize vibration and noise
• Typical symptoms of a failed pad: steam or water at the top of the door near the vent, moisture inside the console, or a rattling vent

• Disconnect power at the breaker and shut off water before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Note pad placement; install the new pad in the same location with clean, dry mating surfaces
• Reassemble and run a short cycle to check the vent area for leaks

This flood hose gasket seals the joint where the washer's flood/overflow hose connects to the outer tub. A fresh seal helps stop seepage from the tub area, preventing drips or moisture around the top or rear of the washer.

• Creates a watertight seal at the flood/overflow hose connection to the outer tub
• Helps prevent leaks during fill, wash, and spin
• Typical failure signs: drips from the top/back of the tub, visible cracks or deformation, or a loose hose connection

• Disconnect power and turn off water supply before servicing
• Access the flood hose connection at the tub; remove the hose and old gasket
• Seat the new gasket fully and reconnect the hose securely
• Run a short cycle to check for leaks

Color: white. It measures about 15 inches wide by 1 inch deep.

This is the magnetic door gasket that seals the fresh food compartment, keeping cold air in and warm air out to maintain temperature and reduce frost and energy loss.

• Creates an airtight seal around the refrigerator (fresh food) door
• Helps maintain proper internal temperature and humidity
• Worn, torn, warped, or hardened gaskets can cause warm spots, sweating/condensation, or excessive run time
• Replace if the door won't seal, you see gaps/light around the door, or the gasket is cracked or misshapen

• Unplug the appliance before servicing
• Soften the new gasket in warm water or with gentle heat to improve flexibility
• Remove the old gasket from the door channel; press the new gasket fully into the groove, working evenly around the perimeter
• Check door alignment and perform a "paper test" to confirm a uniform seal

This gasket creates a tight seal between mating parts in your appliance, helping prevent air, heat, moisture, or combustion byproducts from escaping so the unit runs safely and maintains proper performance. What it does:

• Provides a secure seal between components to prevent leaks
• Supports stable temperatures and airflow inside the appliance
• Minimizes odors, heat escape, and drafts around the sealed area
• Typical failure signs include cracks, flattening, fraying, or persistent leaks

• Disconnect power and, if applicable, shut off gas; allow the unit to cool completely
• Remove retainers/fasteners, take out the old gasket, and clean the mating surfaces
• Position the new gasket without stretching or kinking; align edges/holes and reassemble
• For gas models, perform a leak check with a soapy water solution after reassembly

This drum glide provides a smooth, low-friction surface at the front of the dryer drum. Replacing worn glides restores quiet, even drum rotation and helps prevent scraping and fabric damage.

• Supports the front of the drum and allows smooth rotation on the front bearing/bulkhead
• Reduces friction and metal-on-metal contact to minimize noise and wear
• Helps maintain proper drum alignment and spacing at the door opening
• Common symptoms of a worn glide: scraping or squealing while tumbling, drum hard to turn, brown/black marks on clothes, or snagging at the front edge

• Disconnect power; shut off gas supply for gas dryers before servicing
• Remove the top and front panel/bulkhead to access the front drum support
• Support the drum when the front panel is off to avoid stressing the rear bearing
• Many models use multiple glides; inspect all front support wear items (glides/slides and felt seal) and replace as needed for even wear

This oven door gasket forms a heat-resistant seal between the door and the oven frame. It keeps heat inside the cavity to help the oven reach and maintain set temperatures while limiting steam and odor escape.

• Seals the perimeter of the oven door opening to minimize heat loss and drafts
• Supports accurate temperature regulation and more even baking results
• Helps reduce heat transfer to surrounding surfaces and trim
• Common signs of wear: visible tears or flattening, heat leaking at the door, longer preheat, or temperature fluctuations

• Disconnect electrical power; shut off gas supply
• Pull the old gasket straight out of the door's mounting holes, noting corner orientation
• Press the new gasket's end tabs fully into the holes and seat evenly around the frame—do not stretch
• Close the door and check for uniform contact all around

This oven door gasket forms a heat-resistant seal between the door and the oven frame to keep heat in the cavity. A fresh seal helps the oven preheat properly and maintain consistent temperatures while limiting hot air from escaping.

• Provides a tight thermal seal around the door to reduce heat loss
• Helps stabilize oven temperature and preheat performance
• Replace if the gasket is torn, frayed, brittle, shrunken, or flattened
• Common symptoms of a worn seal: hot air leaking at the door, uneven baking, odors or smoke escaping

• Disconnect power and allow the oven to cool completely
• Remove the old gasket from its channel or end clips; note orientation and seam location
• Clean the groove; press the new gasket in place without stretching, seating corners and ends fully
• Confirm the door closes evenly and seals all around; if not, inspect hinge and latch alignment