Parts for Broan P195: Hood - 1 Motor Parts

This is the aluminum grease filter for a range hood. It traps airborne grease and cooking residue to keep the blower and ductwork cleaner and maintain proper ventilation performance.

• Catches grease and particulates from cooking vapors
• Helps prevent residue buildup on the fan and inside the hood
• Replace if bent, clogged, or when airflow and capture efficiency decline
• Common symptoms: poor venting, visible grease saturation, rattling or loose fit

• Disconnect power to the hood before service
• Access the filter from the underside; release the latch or tabs and slide the old filter out
• Install the new filter with the pull tab/latch oriented as the original
• Check for secure fit and restore power; verify airflow and noise levels

This capacitor helps start and keep the blower/fan motor running smoothly in your range hood or ventilation unit. Replacing a weak or failed capacitor can restore proper fan performance and reduce humming or slow-start issues. What it does

• Provides the phase shift needed for a PSC fan motor to start and run correctly
• Common symptoms of failure: fan won't start, only hums, runs slowly, or starts intermittently
• Physical clues include a swollen case or heat-damaged terminals

• 1 capacitor

• Disconnect power at the breaker before servicing; capacitors can retain a charge
• Safely discharge the old capacitor and avoid shorting the terminals
• Note wire positions/take a photo and transfer wiring to the new part one-for-one
• Mount securely and keep leads clear of sharp edges and hot surfaces; test operation after reassembly

This LED light bulb restores bright, dependable lighting in your range hood so you can clearly see the cooktop while cooking. It replaces the original lamp specified by the manufacturer for models that call for this part number. What it does:

• Provides task lighting from the hood's light socket
• Replaces a bulb that is burnt out, dim, or flickering
• Helps maintain clear visibility over the cooking surface
• Common symptoms include the light not turning on or intermittent operation

• LED light bulb

• Disconnect power to the hood at the breaker before servicing
• Allow the lamp to cool completely before handling
• Access the light from the underside; remove any lens or retaining ring as designed
• Remove the old bulb, seat the new bulb fully, and test before reinstalling the lens/trim

This Heat Sentry is a thermal sensor that detects excessive heat in the hood and helps protect the appliance by triggering a shutdown or alert when temperatures rise above safe levels. It restores proper heat-sensing function for safety. What it does:

• Monitors hood temperature and responds if heat exceeds safe thresholds
• Trips the hood's thermal protection to stop the blower or signal an overheat condition
• Helps prevent damage from prolonged exposure to high heat while cooking
• Common symptom: hood fan stops running or won't restart after heavy cooking, or thermal protection repeatedly trips

• One Heat Sentry thermal sensor

• Turn off power at the breaker before accessing the hood or wiring
• Installation typically requires removing the hood canopy or control panel to reach the sensor
• Match mounting and connector type to your unit; replace only with the same part number

This blower wheel spins inside the vent blower assembly to move air through the hood or ventilation system, restoring proper airflow and helping clear smoke and cooking odors. Fits applications that use a single replacement wheel. What it does:

• Replaces worn or damaged wheel blades that reduce airflow
• Restores proper ventilation when airflow is weak or uneven
• Can reduce vibration or scraping noises caused by a bent or broken wheel
• Works with the blower motor to circulate air through the ductwork and filters

• Disconnect power to the appliance before beginning work.
• Handle with care — blower housings and mounting screws may have sharp edges.
• Verify wheel orientation and secure mounting to the motor shaft per manufacturer alignment marks.

Replacement mounting washer that secures fasteners and maintains proper spacing on blower, motor, and housing assemblies. Restores alignment and helps reduce vibration and rattling caused by loose or missing hardware. What it does:

• Provides a smooth bearing surface under a screw or nut to distribute load and prevent pull-through.
• Keeps mounting fasteners aligned and helps maintain correct spacing between components.
• Helps reduce vibration and noise from loose or worn hardware when installed properly.
• Useful when replacing corroded or damaged fastening hardware during routine repairs.

• Disconnect power to the appliance before beginning any repair.
• Match the washer to the original part (size and thickness) and install between the fastener head and the mounting surface.
• Do not overtighten fasteners—tighten just enough to secure the part and avoid crushing the washer.
• Replace any rusted or damaged screws, nuts, or complementary hardware for a reliable repair.

This push button is a direct-replacement control panel button for range-hood control assemblies. Restores reliable tactile operation for fan and light controls so your hood functions the way it should. What it does

• Replaces a worn, cracked or missing control panel button used to engage fan speeds or lights
• Restores proper contact and tactile feedback when pressed
• Helps stop sticking, intermittent operation or failure-to-engage symptoms related to a damaged button
• Matches OEM fit and appearance for straightforward cosmetic and functional restoration

• Disconnect power to the appliance before starting any repair to avoid shock
• Typically installs by snapping into the control panel; use gentle pressure to seat it fully
• Check alignment with the switch mechanism behind the panel before final seating
• If other control parts are damaged or the switch still fails, replace or test the switch assembly as needed

This factory hardware replaces worn or missing rings used in select Broan ventilation products. It helps secure and space components so they fit correctly and run more quietly, reducing looseness and vibration from fatigued hardware. What it does:

• Retains and spaces mating parts to prevent movement during operation
• Helps maintain proper alignment for smooth, quiet performance
• Restores a snug, rattle-free fit when originals are bent, worn, or missing
• Common signs it's needed: loose or rattling parts, poor fitment, visible damage, or a missing ring during service

• Replacement rings only

• Disconnect power at the breaker before servicing
• Note the original orientation and order of hardware; take photos for reference
• Use appropriate pliers (snap-ring/needle-nose); wear eye protection—small rings can spring free
• Inspect adjacent parts for wear and replace any damaged components to ensure a secure fit

This grille stroke is the replacement vent grille component that helps position and secure the range-hood grille for proper fit and quieter operation. It restores correct grille alignment and reduces vibration-related noise. What it does:

• Secures and positions the vent grille so it sits flush and aligns with the hood opening
• Helps prevent grille movement and rattling during fan operation
• Restores correct contact points that keep the grille from sagging or falling out
• Common symptoms resolved: loose or misaligned grille, grille that vibrates or won't stay seated

• Disconnect power to the hood before starting any work
• Typically accessed by removing the grille; basic hand tools may be required
• Handle parts gently to avoid scratching the grille or surrounding finish
• Test grille fit and fan operation after installation

This light bulb socket restores a secure, reliable connection for your appliance's lamp. It holds the bulb firmly and supplies power so your workspace stays well lit whenever you switch the light on. What it does:

• Provides the electrical contact and mechanical support for the light bulb
• Helps resolve no-light or intermittent/flickering light when a good bulb is installed
• Replaces sockets with heat damage, discoloration, or corroded contacts
• Ensures proper bulb seating for consistent illumination

• 1 light bulb socket

• Disconnect power at the breaker and allow the area and bulb to cool before servicing
• Remove any lens or cover carefully and support glass to prevent drops
• Transfer wires one at a time to maintain correct connections, following your model's wiring diagram
• Install only the bulb type and wattage specified for your model and confirm the bulb seats fully