Parts for Frigidaire GRSS2652AD1: Ice & Water Dispenser Parts

This refrigerator water tube carries water between internal components such as the inlet valve, filter/reservoir, dispenser, or ice maker. Replacing a brittle, kinked, or leaking tube helps restore proper water flow and prevents messy leaks. What it does:

• Routes water within the refrigerator's water and ice system
• Helps deliver water to the dispenser and/or ice maker
• Common symptoms of a bad tube: leaks, poor dispenser flow, no ice production, visible cracks/kinks, or dripping at connections
• Restores dependable water delivery when tubing is damaged

• 1 water tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the tube's routing and connection points; take photos for reference
• Cut tubing ends squarely if trimming and fully seat into existing fittings
• Turn water back on and check all connections for leaks; flush the system to clear air

This housing is the main structural enclosure that supports and protects internal components, restoring proper alignment and safe operation. It replaces a damaged or cracked outer housing to reduce vibration and protect wiring and moving parts. What it does

• Provides structural support and mounting points for internal components.
• Protects internal parts from debris and physical damage.
• Helps reduce vibration and rattling caused by a cracked or broken housing.
• Restores proper alignment to maintain correct component clearances.

• One housing main assembly.

• Disconnect power and, if applicable, gas supply before starting any repair.
• Handle carefully to avoid damaging mounting tabs or paint; some trimming may be required for perfect fit on older units.
• If any fasteners, clips, or gaskets are worn or missing, replace them to ensure a secure installation.

This plastic guide positions and supports a moving component inside the appliance to keep parts aligned and running smoothly. Replacing a worn guide restores proper fit and helps reduce rubbing noises and uneven movement. What it does:

• Holds and aligns a moving part or trim so it tracks correctly during operation
• Prevents rubbing, scraping, or binding that can cause noise or premature wear
• Maintains correct spacing to protect adjacent components from damage
• Commonly replaced when you see misalignment, clicking, or intermittent contact

• One plastic guide as shown

• Disconnect power (and water, if applicable) before attempting any repair
• Access may require removing panels or trim; keep fasteners organized
• Inspect adjacent parts for wear and replace if needed to prevent repeat failure

Replacement drip pan that catches defrost and condensation water beneath the appliance to help keep the cabinet floor dry and reduce the chance of visible leaks or puddling. Simple swap to restore proper water collection. What it does

• Collects defrost and condensation water to channel it away from the cabinet floor.
• Helps prevent water stains and puddles under the appliance.
• Replaces cracked, warped, or missing factory trays that cause leaks or odors.
• Works with the appliance's drainage path to reduce floor-level moisture.

• One replacement tray.

• Disconnect power to the appliance before servicing.
• Remove contents, shelves or access panels as needed to reach the tray.
• Slide or snap the old tray out and position the new tray in the same orientation; secure any clips or fasteners used by the original part.

This user interface is the front control panel assembly that lets you select oven and cooktop functions and read status feedback. It restores responsive touch/buttons and visible display captions so controls operate and display correctly. What it does:

• Provides the keypad/buttons and display used to choose bake, broil, timer and other oven functions
• Sends user commands to the range's control board so selected cycles start and stop
• Restores visible status and error indicators when cracked, unresponsive, or dim display segments appear
• Helps resolve symptoms such as non-working buttons, incorrect display readout, or no response to touch/press inputs

• One user interface/control panel assembly

• High-level replacement; disconnect power at the breaker before beginning
• May require removing outer control panel trim or console screws to access mounting and electrical connectors
• Match connector orientation and secure ribbon or wire harnesses; avoid bending contacts
• Test function after install to ensure issue is resolved

This replacement electrical switch controls power to a specific function in your appliance. By opening or closing the circuit, it lets the selected feature turn on and off reliably when you actuate the control.

• Completes or breaks the circuit to start/stop its assigned component
• Restores responsive on/off or selector operation at the control
• Common failure symptoms: feature won't start or won't shut off, intermittent operation, loose/stuck actuator, or heat discoloration on the old switch
• Used in control, console, or door areas depending on model design

• Disconnect appliance from power before servicing
• Access the switch location per your model; remove knob/panel if applicable
• Photograph wire positions and note terminal labels (COM/NO/NC) if present; transfer wires one at a time to the new switch
• Secure mounting, ensure tight connectors, reassemble, restore power, and test operation

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This tension spring provides the restoring force needed for a moving refrigerator component, helping parts return to their normal position for reliable operation and alignment. It's a simple replacement that restores proper movement and stability. What it does:

• Provides tension to return or hold a component in place during normal operation
• Helps maintain proper alignment and smooth movement of the associated mechanism
• Worn or broken springs can cause improper latching, sagging, or uneven movement
• Replacing a damaged spring often resolves related noise or binding issues

• One replacement spring

• Disconnect power before attempting any repairs to avoid electrical hazards
• Handle springs carefully; they can be under tension and may require basic tools to remove/install
• Replace with the exact part number to ensure fit and function

This water inlet tube routes potable water from the refrigerator's inlet/valve to the dispenser and ice-making components, helping restore normal water delivery and prevent leaks when damaged. What it does

• Channels water from the inlet valve to the dispenser/ice maker assembly.
• Replaces cracked, kinked, or clogged tubing that can cause leaks or reduced flow.
• Helps stop visible dripping, puddling, or intermittent water flow at the dispenser.
• Works as a direct-fit plumbing replacement when the original tube is damaged.

• One water inlet tube

• Turn off refrigerator power and shut off the water supply before starting.
• Inspect fittings and seals; replace any damaged ferrules or gaskets for a watertight connection.
• Use basic hand tools; avoid sharp bends or kinks when routing the tube.
• After installation, restore water and power, then check all connections for leaks.

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle