Parts for Frigidaire FRSS2623AB0: Ice & Water Dispenser Parts

This refrigerator water tube carries water between internal components such as the inlet valve, filter/reservoir, dispenser, or ice maker. Replacing a brittle, kinked, or leaking tube helps restore proper water flow and prevents messy leaks. What it does:

• Routes water within the refrigerator's water and ice system
• Helps deliver water to the dispenser and/or ice maker
• Common symptoms of a bad tube: leaks, poor dispenser flow, no ice production, visible cracks/kinks, or dripping at connections
• Restores dependable water delivery when tubing is damaged

• 1 water tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the tube's routing and connection points; take photos for reference
• Cut tubing ends squarely if trimming and fully seat into existing fittings
• Turn water back on and check all connections for leaks; flush the system to clear air

This dispenser module is the replacement control assembly for your refrigerator's dispenser — it restores dispenser switch and actuator functions so you can reliably dispense water or ice from the door. What it does

• Replaces the dispenser control/actuator that registers lever presses and sends signals to the dispenser system
• Can stop intermittent or non-responsive dispenser activation when the module has failed
• Helps restore normal dispenser operation without replacing the full door assembly
• Fits into the dispenser housing and connects to the dispenser wiring harness

• Includes: one dispenser module (control assembly)

• Disconnect power (and water supply if applicable) before starting work
• Remove the dispenser bezel or inside door panel to access and replace the module
• Handle electrical connectors carefully; confirm connectors are fully seated before testing

This dispenser module is the electronic control that manages dispenser functions and user inputs. Replacing a failed module restores proper dispenser responsiveness and front-panel operation so selections register and dispense as intended. What it does:

• Interprets dispenser button/paddle inputs and controls dispensing functions
• Powers and manages the dispenser's display/indicators (on applicable models)
• Common fix for dead/unresponsive dispenser controls or display
• Helps resolve intermittent or erratic dispenser operation

• 1 dispenser module

• Disconnect power before servicing; turn off water supply if working near dispenser plumbing
• Handle the board by the edges and use ESD protection
• Note/photo wire connections; transfer any brackets/overlay from the original as needed
• After installation, restore power and test all dispenser functions

The Dispenser Module is an OEM part for Frigidaire refrigerators. It controls the water and ice dispensing functions, providing access to water and ice.

A bad dispenser module can be caused by electrical issues, mechanical failure, or damage to the internal components. When the module becomes faulty, it can result in issues such as a non-responsive dispenser, inconsistent water flow, or ice dispensing problems.

Symptoms of a bad dispenser module include:

• No water or ice dispensing
• Inconsistent water flow or low water pressure
• Not dispensing crushed ice

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This water inlet tube routes potable water from the refrigerator's inlet/valve to the dispenser and ice-making components, helping restore normal water delivery and prevent leaks when damaged. What it does

• Channels water from the inlet valve to the dispenser/ice maker assembly.
• Replaces cracked, kinked, or clogged tubing that can cause leaks or reduced flow.
• Helps stop visible dripping, puddling, or intermittent water flow at the dispenser.
• Works as a direct-fit plumbing replacement when the original tube is damaged.

• One water inlet tube

• Turn off refrigerator power and shut off the water supply before starting.
• Inspect fittings and seals; replace any damaged ferrules or gaskets for a watertight connection.
• Use basic hand tools; avoid sharp bends or kinks when routing the tube.
• After installation, restore water and power, then check all connections for leaks.

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle