Parts for Frigidaire FRSS2623AB4: Ice & Water Dispenser Parts

This replacement tube routes refrigerant-cycle condensate and defrost water away from the evaporator area to the drain pan, helping stop pooling and prevent leaks that can damage cabinets or cause odor. Easy direct-replacement when the original tube is cracked or clogged. What it does

• Channels defrost and condensate water from the evaporator area to the drain pan.
• Helps prevent water pooling inside the fresh food or freezer section.
• Reduces risk of leaks that can cause floor damage or moldy odors.
• Can restore proper defrost drainage when the original tube is crushed, cracked, or blocked.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• If applicable, turn off the water supply and drain any residual water before removing connections.
• Inspect surrounding seals and grommets; replace if worn to ensure a watertight fit.
• After installation, run a short cycle or pour a small amount of water into the evaporator area to ensure proper drainage.

This main electronic control board manages the appliance's user interface, timing, and cycle functions so the unit responds correctly to commands. Replacement restores electronic control of cycles, displays, and safety interlocks when the original board fails. What it does:

• Receives input from the keypad/touchpad and runs the appliance's programmed cycles and timers
• Controls power to heating elements, motors, valves, and other subsystems via relays/triacs
• Monitors and displays status information and error codes to the user interface
• Commonly replaces a board when the control is unresponsive, buttons or display fail, or cycles do not start

• One electronic control board

• Disconnect power to the appliance before beginning service to avoid shock or injury
• Handle the board by its edges and avoid touching components; observe ESD (static) precautions
• Compare the part number on the old board to ensure exact match before installing

The Dispenser Module is an OEM part for Frigidaire refrigerators. It controls the water and ice dispensing functions, providing access to water and ice.

A bad dispenser module can be caused by electrical issues, mechanical failure, or damage to the internal components. When the module becomes faulty, it can result in issues such as a non-responsive dispenser, inconsistent water flow, or ice dispensing problems.

Symptoms of a bad dispenser module include:

• No water or ice dispensing
• Inconsistent water flow or low water pressure
• Not dispensing crushed ice

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This is a factory replacement screw fastener used to secure components in your appliance. It restores a tight, rattle-free fit for panels, brackets, and trim when an original screw is missing, stripped, or corroded.

• Secures panels, brackets, and trim to the appliance cabinet or liner
• Replaces a missing, stripped, or rusty screw
• Helps eliminate looseness, vibration, or rattling components
• Maintains proper alignment and a clean, factory fit

• Unplug the appliance before servicing; if near water lines, shut off the supply
• Match to the original and install in the same location/orientation
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Keep and reuse any original washers or spacers if present

This water inlet tube routes potable water from the refrigerator's inlet/valve to the dispenser and ice-making components, helping restore normal water delivery and prevent leaks when damaged. What it does

• Channels water from the inlet valve to the dispenser/ice maker assembly.
• Replaces cracked, kinked, or clogged tubing that can cause leaks or reduced flow.
• Helps stop visible dripping, puddling, or intermittent water flow at the dispenser.
• Works as a direct-fit plumbing replacement when the original tube is damaged.

• One water inlet tube

• Turn off refrigerator power and shut off the water supply before starting.
• Inspect fittings and seals; replace any damaged ferrules or gaskets for a watertight connection.
• Use basic hand tools; avoid sharp bends or kinks when routing the tube.
• After installation, restore water and power, then check all connections for leaks.

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle