Parts for Frigidaire FFSS2615TP0: Ice & Water Dispnser Parts

This single-pack Frigidaire PureSource 3 WF3CB Water Filter is an OEM replacement part for Frigidaire refrigerators. It improves the quality and taste of your drinking water. It removes impurities such as lead, cysts, and mercury, as well as reduces chlorine taste and odor. The filter is NSF and WQA certified and is designed to fit specific side-by-side models after 2009 where the filter is located in the back, right top. 

Specs:

• Pressure range: 30 - 100 PSIG
• Color: White
• Dimensions: Approximately 2-1/2 inches in diameter by 9-1/2 inches deep.

To ensure optimal performance, filters should be changed every 6 months or 200 gallons, depending on usage. 

This refrigerator water tube carries water between internal components such as the inlet valve, filter/reservoir, dispenser, or ice maker. Replacing a brittle, kinked, or leaking tube helps restore proper water flow and prevents messy leaks. What it does:

• Routes water within the refrigerator's water and ice system
• Helps deliver water to the dispenser and/or ice maker
• Common symptoms of a bad tube: leaks, poor dispenser flow, no ice production, visible cracks/kinks, or dripping at connections
• Restores dependable water delivery when tubing is damaged

• 1 water tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the tube's routing and connection points; take photos for reference
• Cut tubing ends squarely if trimming and fully seat into existing fittings
• Turn water back on and check all connections for leaks; flush the system to clear air

This replacement cover restores a clean, finished look and protects the designated area of your appliance. Replacing a damaged or missing cover helps keep components shielded and secure so the unit functions and looks as intended. What it does:

• Shields and conceals the specific opening or component it's designed for
• Helps prevent debris and accidental contact with internal parts
• Restores proper fit and appearance when the original cover is cracked or missing
• Common signs it's needed: broken tabs, cracks, warping, or a cover that won't stay in place

• 1 cover

• Disconnect power before servicing
• Remove any retaining screws or release tabs; note orientation for reassembly
• Transfer and reuse original screws/clips if applicable
• Do not overtighten fasteners to avoid cracking the new cover

The refrigerator dispenser cover module is an OEM part for Frigidaire refrigerators. This grey module serves as an aesthetic cover that helps protect the dispenser mechanism. It is designed to blend in with the exterior of the refrigerator sheltering its internal components. 

Causes of a bad dispenser cover can include wear and tear over time, exposure to impacts or damage, or cracks that compromise its protective functionality. 

Symptoms of a bad dispenser cover include:

• Exposure of internal dispenser parts  
• Leaks around the dispenser area
• Loose or misaligned fit within the refrigerator
• Cracks or splits in the plastic material

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dispenser Cover is an OEM replacement part for Frigidaire side-by-side refrigerator models. Located on the refrigerator door, it provides external closure over the built-in dispenser features.

Causes of a bad cover can include cracks or chips developing from repeated use of the dispensers, and exposure to impacts/cleaning chemicals compromising plastic integrity over time.  

Symptoms include:

• Water or debris accumulating in cracks or crevices   
• Weakened hinges unable to maintain proper closure position  
• Fading, dulling, or discoloration compared to surrounding finishes

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore refrigerators. 

The Dispenser Module is an OEM part for Frigidaire refrigerators. It is an electronic component that controls the dispensing functions within the appliance's door or panel. This includes releasing filtered water, ice, and crushed ice on demand.

Causes of a bad dispenser module can include component malfunctions, circuit failures, or software glitches interrupting the dispensing process. 

Symptoms of an issue include:

• The dispenser not releasing any water, ice or crushed ice when tapped  
• Dispensing inconsistent amounts or none at all between uses
• Error codes shown related to the dispenser functions
• Operational noises from the dispenser that shouldn't occur

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Dispenser Module is an OEM part for Frigidaire refrigerators. It is a component located within the refrigerator door that is responsible for dispensing water and ice. The dispenser module houses the necessary valve assemblies, sensors, actuators and tubing required to deliver chilled water and ice on demand when the dispenser lever is engaged. It is designed to seamlessly integrate within the refrigerator door panel for convenient access.

Causes of a bad dispenser module can include buildup of mineral deposits or contaminants within the internal components that disrupt water flow or sensor functions over time. Mechanical wear and tear of plastic or rubber seals and valves is also common.

Symptoms of a bad dispenser module include:

• Slow or intermittent water flow from the dispenser
• Ice cubes dispensed one at a time instead of in batches
• Water or ice dispensing that doesn't work at all
• Leaks or water droplets below the dispenser area
• Error codes related to the dispenser on the control board

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Dispenser Module is an OEM part for Frigidaire refrigerators. This module controls the dispensing of ice and water from the refrigerator.  

Causes of a bad dispenser module can include electrical failures, worn-out components, or damage from regular use.  

Symptoms of a bad dispenser module include:

• The dispenser not responding to button presses
• No water or ice being dispensed
• Intermittent or inconsistent dispensing
• Display or control panel malfunctions

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The refrigerator dispenser module overlay is an OEM part for Frigidaire refrigerators. This overlay sits atop the dispenser module providing additional protection and aesthetic appeal.

Symptoms of a bad dispenser overlay include:

• Cracks or breaks exposing underlying parts
• Misalignment or looseness within the refrigerator 
• Discoloration or wear affecting appearance
• Inability to fully or securely cover the dispenser module

Causes of a bad overlay can include damage from impact, repeated opening and closing of the refrigerator door, or general wear over time. 

This Frigidaire OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dispenser Module Cover is an OEM part for Frigidaire Refrigerator. It is the decorative plastic shroud that fits externally over the ice and water dispenser components.

Causes can be normal wear from frequent use of the dispenser, impacts from children or pets pressing on the area, or damage from attempted cleaning with improper chemicals over time.

Symptoms of a bad dispenser module cover include:

• Cracked, faded or stained external appearance
• Exposed wires and components vulnerable to liquid intrusion
• Cover not properly sitting flush or securely clipping into place

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

The Dispenser Cover Overlay is an OEM part for Frigidaire refrigerators. This part fits over the front of the dispenser, providing a protective and decorative cover for the control panel and dispenser mechanisms.  

Causes of a bad dispenser cover overlay can include physical damage from impacts, wear and tear from frequent use, or fading and discoloration from prolonged exposure to sunlight and cleaning chemicals.  

Symptoms of a bad dispenser cover overlay include:

• Cracks or breaks in the cover
• Discoloration or fading of the overlay
• Difficulty using the dispenser controls
• The overlay peeling or coming loose from the dispenser

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Drip Tray is an OEM replacement part that fits Frigidaire refrigerators. It is responsible for catching water drips and spills under the water dispenser. Over time, the tray can crack or warp leading to leaks. Causes of failure include loss of the part, accidental damage, and wear over time. 

Symptoms of a failing drip tray include:

• water on the floor
• improper fit allowing leaks
• cracks or breaks in the tray

The drip tray is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, Crosley, and Kenmore refrigerator models

The Drip Tray is an OEM replacement part that fits Frigidaire refrigerators. It is responsible for catching water drips and spills under the water dispenser. Over time, the tray can crack or warp leading to leaks. Causes of failure include loss of the part, accidental damage, and wear over time. 

Symptoms of a failing drip tray include:

• water on the floor
• improper fit allowing leaks
• cracks or breaks in the tray

The drip tray is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, Crosley, and Kenmore refrigerator models

The Dispenser Drip Tray is an OEM replacement part for Frigidaire refrigerators. It is located below the water and ice dispenser and collects any accidental spills or drips that occur during use. The drip tray helps prevent moisture accumulation on interior surfaces that could lead to mold or mess. It measures about 11 inches wide by 4 inches deep.

Symptoms of a bad dispenser drip tray include:

• Unpleasant odors emanating from unaddressed spills or drips
• Visible water staining or residue buildup below dispenser

Causes of failure are typically just general wear and tear from prolonged use. 

This replacement part is also compatible with models produced by Electrolux, Gibson, Kelvinator, and Kenmore. 

The Switch-4 Button Assembly is an OEM part for Frigidaire refrigerators. This switch assembly operates important refrigerator functions like the light controls, temperature selection, and ice/water dispenser functions. It contains four precise switches designed to last through years of use while maintaining accurate input control.

Causes of a bad switch assembly can include continuous actuations over time leading to switch wear, accidental damage or spills compromising switch integrity, or failures in electronic components.

Symptoms of a bad switch assembly include:

• Lights or temperature settings not functioning properly
• Ice/water dispenser buttons not working as expected
• Failed or improperly actuating switches
• Water leaks or electrical issues at the switch location

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This dispenser heater kit warms the dispenser area to help prevent ice build-up and keep the water/ice dispenser operating reliably. Replaces a failed heater assembly to restore proper dispenser function. What it does:

• Heats the dispenser chute/valve area to reduce frost and ice clogging
• Helps restore reliable water or ice dispensing when the dispenser intermittently freezes
• Prevents repeated thaw cycles that can cause leaks or inconsistent dispense flow
• Works as the direct replacement heater component used in the dispenser assembly

• Disconnect power to the appliance before beginning any work
• Access may require removing the dispenser housing or control panel
• Handle electrical connections carefully and secure wiring per OEM routing

This water inlet tube routes potable water from the refrigerator's inlet/valve to the dispenser and ice-making components, helping restore normal water delivery and prevent leaks when damaged. What it does

• Channels water from the inlet valve to the dispenser/ice maker assembly.
• Replaces cracked, kinked, or clogged tubing that can cause leaks or reduced flow.
• Helps stop visible dripping, puddling, or intermittent water flow at the dispenser.
• Works as a direct-fit plumbing replacement when the original tube is damaged.

• One water inlet tube

• Turn off refrigerator power and shut off the water supply before starting.
• Inspect fittings and seals; replace any damaged ferrules or gaskets for a watertight connection.
• Use basic hand tools; avoid sharp bends or kinks when routing the tube.
• After installation, restore water and power, then check all connections for leaks.

This refrigerator water inlet tube channels water from the valve into the internal dispensing/ice system. Replace a cracked, kinked, or clogged tube to restore proper flow and help stop leaks at the rear or inside the cabinet.

• Routes water from the inlet valve to the refrigerator's water system
• Helps resolve leaks, weak/no dispenser flow, or no ice production due to damaged or restricted tubing
• Replaces brittle, cracked, or kinked tubing that can cause drips or water damage
• Maintains a sealed path when properly seated in the existing fittings

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure; place a towel/pan to catch residual water
• Note the original routing; transfer any reusable clips/fittings from the old tube
• Cut ends square if required, push fully into couplers, restore water, and check carefully for leaks before reconnecting power

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

The Ice Maker Fill Tube Assembly is an OEM replacement part for Frigidaire refrigerators. As a component of the automatic icemaker, this fill tube assembly transports water from the water supply line into the ice molding chamber.

Causes of a bad fill tube assembly can include cracks, leaks, or blockages developing over time due to mineral buildup or mold growth inside the plastic tubing. Constant bending during ice production also leads to tubing fatigue.

Symptoms of a bad fill tube assembly include:

• Icemaker not filling with water or producing ice
• Water leaks in the freezer compartment
• Mineral residue or mold observed inside the tubing

This OEM Frigidaire part is compatible with models including Electrolux, Gibson, Kelvinator, and some Kenmore units.