Parts for Thermador PRG486EDG01: Large Oven Parts

This surface burner replaces a damaged or worn cooktop burner to restore even, reliable heating for gas ranges and cooktops. It fits into the burner base and provides the proper flame pattern for cooking performance. What it does:

• Directs gas to the cooktop slot so the burner produces a controlled flame for cooking
• Restores even heating when an old burner causes uneven cooking or hot spots
• Helps eliminate weak or irregular flames caused by dents, warping, or corrosion
• Works with the existing burner base and ignition system when correctly matched

• One surface burner

• Turn off the appliance's gas and power before removing or installing the burner
• Remove grate and any clips or screws holding the old burner; seat the new burner securely in the burner base
• Clean surrounding surfaces and ports of debris before installation to ensure proper flame pattern

The Bake Igniter is an OEM part for Bosch wall ovens and ranges. Located at the bottom of the oven cavity, it generates the radiant heat needed to initiate the bake burners.

Causes of a bad bake igniter can include failure of the delicate calrod-style heating element from prolonged high-temperature exposure over time.

Symptoms of a bad bake igniter include:

• Inability to ignite or maintain ignition of the bake burners
• Improperly or unevenly heated oven cavity
• Cool or cold spots appearing on bake results
• Igniter glows, but fails to ignite

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The temperature sensor is an electronic probe that monitors internal appliance temperature and reports it to the control so it can regulate operation. Replacing a failed sensor restores more accurate temperatures and can clear temperature-related error codes. What it does:

• Senses internal temperature via resistance changes and sends the signal to the electronic control
• Helps the control reach and maintain the set temperature during operation
• Common failure symptoms: too hot/cold, won't reach set temp, long/short cycles, temperature error codes
• Can cause preheat to stall or the unit to shut off early (model dependent)

• Includes: 1 temperature sensor

• Disconnect power at the breaker before servicing
• Location and access vary by model; typically mounts with screws or a clip and connects to a 2-wire harness
• Handle the connector and wiring carefully; route and secure away from hot or moving parts
• After installation, clear stored errors and run a test cycle to proper readings

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

This fan cover protects the appliance's blower assembly and directs airflow to maintain proper ventilation. It helps prevent debris from reaching the fan and supports efficient air movement for reliable operation. What it does:

• Shields the blower/fan from dust, lint, and loose debris that can interfere with airflow
• Directs and channels airflow for consistent ventilation and cooling of internal components
• Helps reduce noise by enclosing the fan area and stabilizing the blower assembly
• Commonly replaced when cracked, damaged, or warped after impact or wear

• One fan cover

• Inspect surrounding seals and mounting tabs before installation; replace any broken clips
• Power off and disconnect the appliance before accessing internal components
• May require basic tools (screwdriver, socket) and removal of adjacent panels for access

This bottom cavity cover replaces the removable floor panel under the oven cavity to protect internal components and help contain spills for easier clean-up. It restores the oven's lower interior surface for safe, tidy operation. What it does:

• Covers and protects the oven cavity floor and components from drips, crumbs, and direct heat exposure
• Helps keep the lower oven area clean and makes wiping up spills simpler
• Supports proper airflow path and component protection when installed
• Commonly replaced when the original cover is dented, warped, or damaged

• One bottom cavity cover

• Turn off and disconnect power to the appliance before starting any repair
• Allow the oven to cool completely; use gloves to handle sharp edges
• Installation typically requires removing the oven racks and sliding the cover into position; keep fasteners if present