Parts for Speed Queen LDGE5BGS113TW01-THRU-S#1912999999: Lint Filter Parts

A replacement self-tapping screw used to secure plastic trim and sheet-metal panels on laundry equipment. Durable washer-head design helps distribute load and resist pull-through in plastic mounting points. What it does

• Fastens panels, trim pieces, and components where a short sheet-metal screw is required
• Self-tapping tip forms threads in plastic or thin metal for a secure hold
• Washer-style head spreads clamping force to reduce damage to plastic parts
• Common repair for missing, stripped, or broken mounting screws that cause loose panels or rattling

• One self-tapping screw (12-16 x 0.562 in) with hex washer head

• Use the correct screwdriver or low-torque driver to avoid over-tightening into plastic
• Start by hand-threading, then finish with short, controlled driver pulls
• Disconnect power and follow all safety guidance for the appliance before servicing
• Replace any damaged mating threads or inserts to ensure a secure repair

This lint filter captures lint and fibers from the drying airflow to protect the blower and vent path. Replacing a damaged or missing screen helps maintain airflow, reduce lint buildup, and keep drying performance consistent.

• Traps lint and debris as air circulates through the dryer
• Helps maintain proper airflow and drying efficiency
• Replace if mesh is torn, frame is warped/cracked, or the filter won't seat fully
• Common symptoms: longer dry times, lint on clothes or around the door, or a filter that pops out

• Disconnect power; for gas models, also shut off the gas supply
• Remove the old filter from the lint opening and vacuum any lint from the housing
• Insert the new filter fully so it sits flat and seals properly
• Never operate the dryer without the lint filter installed

This lint filter traps lint and fibers as air moves through the dryer, helping maintain proper airflow and drying performance. Replace a damaged or missing screen to reduce lint buildup inside the machine and along the vent.

• Captures lint and debris during the drying cycle to protect the blower and venting
• Helps maintain airflow for consistent drying results and temperature control
• Reduces lint redepositing on clothes and around the door opening
• Replace if the mesh is torn, the frame is warped/cracked, or if you notice longer dry times or excess lint inside the drum

• Disconnect power before servicing
• Remove the old screen and vacuum out the lint chute/housing; inspect and clean the exhaust vent as needed
• Insert the new filter and ensure it seats fully and flush—do not operate the dryer without the filter in place
• Run a short test cycle to confirm proper airflow at the exhaust

This light gray lint filter cover shields the dryer's lint screen opening and helps direct airflow for efficient lint capture. Replace a cracked or missing cover to maintain airflow and reduce the chance of fabric snags.

• Covers the lint screen opening and channels air through the filter
• Helps keep the lint screen aligned and properly seated
• Provides a smooth edge at the door opening to protect fabrics
• Typical signs it's failing: cracks, broken tabs, loose lint screen, lint in drum, longer dry times

• Disconnect power before servicing
• Open the door; remove screws or release locking tabs to remove the old cover
• Position the new cover and secure it with existing hardware as applicable
• The lint screen slides in fully and seats flush before use

This lint filter cover fits over the dryer's lint screen opening to secure the filter and provide a smooth, directed airflow path. Replace a cracked or missing cover to help maintain lint capture and protect fabrics at the opening.

• Covers the lint filter opening and holds the screen in place
• Guides air through the filter to collect lint
• Provides a smooth edge to help prevent fabric snags at the drum entrance
• Typical signs of failure: cracked/broken cover, loose or mis-seated lint screen, excess lint in the drum, or longer dry times

• Disconnect power; for gas models, shut off the gas supply
• Open the door and remove the lint screen
• Remove the existing cover by releasing its fasteners/tabs (varies by model); note orientation
• Seat the new cover securely and reinstall the lint screen; verify proper fit before use