Parts for Speed Queen ADEE9BSS175TN01-THRU-S#1912999999: Loading Door Parts

Sturdy metal door strike that mates with the latch/lock on your machine's cabinet. It keeps the door closed and engages the door switch so cycles can start and run without nuisance stops.

• Interfaces with the door latch/lock mechanism to secure closure
• Engages the door switch/interlock so the appliance can start and continue running
• Restores proper door alignment and latch feel after wear or bending
• Typical symptoms: door won't latch or pops open; unit won't start/run; intermittent stopping mid-cycle; visible damage to the strike

• Unplug the appliance (and shut off gas to gas dryers) before servicing
• Remove the existing strike and retain mounting hardware; note orientation
• Install the new strike in the same position; tighten screws and verify alignment
• Close the door to confirm smooth latching and proper operation

This door seal creates a tight, protective barrier around the dryer door to help contain heat, airflow and lint for efficient drying and safer operation. It replaces worn or torn seals that let air escape or allow excess lint buildup. What it does:

• Seals gap between the door and cabinet to maintain proper airflow and drying temperature
• Helps prevent lint, dust and small items from escaping the drum area
• Reduces heat loss that can lengthen dry times or lower performance
• Stops drafts and minimizes air leaks that can cause uneven drying

• Disconnect power before beginning any service to avoid shock or injury
• Remove the door and/or access panel per your model's service instructions to reach the seal
• Inspect the door frame and mating surfaces; clean away lint and residue before installing the new seal
• If clips or adhesive are used in your model, replace or resecure them per manufacturer guidance

This grill door liner is the inner-facing trim piece that restores the dryer/grill door's appearance and protects the door opening from wear. It replaces cracked, warped, or discolored liners to give a clean, finished look. What it does:

• Covers and protects the door opening edge from heat, lint, and everyday wear
• Restores a smooth, uniform interior door surface after damage or discoloration
• Helps keep the door seal area aligned and reduces gaps where lint or debris can collect
• Improves appliance appearance when the original liner is cracked, warped, or peeling

• One grill door liner (white)

• Designed to fit the original mounting points; inspect existing hardware and retain any reusable clips/screws
• Turn off and unplug the appliance before starting work; allow surfaces to cool
• Use basic hand tools; avoid forcing the liner into place to prevent cracking

This is a 8-16 x 5/8 tapping screw with a #6 Phillips drive, used to fasten panels and components on compatible appliances. It provides a secure, low-profile hold for trim, brackets and covers. What it does:

• Secures panels, trim pieces, brackets or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment and fit of exterior or interior panels
• Provides a threaded connection in sheet metal or tapped holes

• Use the correct #6 Phillips screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure alignment, then tighten until snug — do not overtighten
• Replace stripped or damaged screws to ensure secure fastening
• Wear eye protection and disconnect power to the appliance before working on components

This door hinge secures and lets the appliance door pivot smoothly, restoring proper alignment and reliable opening/closing. A direct-fit replacement designed to return worn or damaged hinges to correct function. What it does:

• Supports the door and provides a pivot point for opening and closing
• Restores proper door alignment and prevents sagging or uneven gaps
• Helps the door latch and seal correctly by maintaining hinge position
• Common symptom fix: loose, noisy, tilted, or non-closing door

• Disconnect power and water before beginning any repairs
• Support the door during removal/installation to prevent dropping or damage
• Use the factory mounting screws and torque to OEM spec; replace damaged fasteners
• If alignment or latch issues persist after install, check strike and door seal for wear or damage

A replacement wedge for the door handle that restores a secure grip and smooth door operation. Fits the white trim area of the handle assembly to replace cracked, broken, or worn wedges and improve door feel. What it does:

• Replaces a damaged or missing wedge piece that holds the door handle trim in position.
• Restores a stable gripping surface so the door opens and closes without slipping.
• Helps correct symptoms such as a loose, cracked, or partially detached handle wedge.
• Matches the white finish used on the handle trim for a consistent appearance.

• One white wedge door-handle piece as shown

• Disconnect power to the appliance before starting any repair.
• Installation typically requires basic hand tools; remove the handle/trim to access the wedge.
• Align the wedge and snap or fasten into place without forcing; avoid over-tightening fasteners.

This solid stainless-steel dryer door replaces a damaged or dented outer door panel to restore the dryer's appearance and proper closure. It offers a durable, corrosion-resistant finish that matches stainless models and supports the latch and hinges. What it does:

• Replaces a dented, scratched, or bent dryer outer door panel to restore fit and finish
• Provides a corrosion-resistant stainless surface that resists wear and maintains appearance
• Allows the door latch and hinge assembly to secure properly for normal operation
• Helps prevent air leaks by restoring proper door alignment

• One solid stainless-steel dryer outer door panel

• Disconnect power to the dryer before beginning any work to reduce shock/fire risk
• Removal typically requires removing the old door from hinge/pivot screws and transferring the latch/handle
• Handle and latch may need to be transferred from the old door