Parts for Lg LDE3031ST: Lower Cavity Parts

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

The Oven Rack is an OEM part for LG ranges. This part provides a stable surface for placing cookware during baking, roasting, and broiling.

Causes of a bad oven rack can include exposure to high temperatures over time, which can weaken the metal, or accidental damage that causes bending or warping.  

Symptoms of a bad oven rack include:

• Warping or bending of the rack
• Difficulty sliding the rack in and out of the oven
• The rack not sitting level within the oven

This OEM LG part is also compatible with some Kenmore models.

The Time Delay Fuse is an OEM part for LG microwaves. This fuse provides a safety mechanism by delaying the flow of electricity, protecting the microwave's electrical components from power surges and ensuring the appliance operates safely. It helps to prevent immediate damage in the event of a power surge or electrical fault, thus prolonging the lifespan of the microwave.

Over time, the time delay fuse can become damaged due to electrical surges, wear and tear, or faulty connections. If the fuse blows, it can disrupt the microwave’s ability to function correctly.

Symptoms of a bad time delay fuse include:

• The microwave not turning on
• No response from the microwave control panel
• The microwave stopping unexpectedly during operation
• Electrical issues or blown circuits in the microwave

This OEM LG part is also compatible with Sears/Kenmore models.

This control panel assembly is the front user interface that holds the touchpad/buttons and display, restoring responsive controls and a finished look to the appliance. It replaces a cracked, faded, or unresponsive front control surface. What it does

• Provides the front-mounted buttons/touchpad and display lens used to select cycles and functions.
• Routes user input to the appliance's control electronics so commands register correctly.
• Restores a damaged, cracked, or scratched control surface that interferes with button use.
• Helps address symptoms such as unresponsive or stuck buttons, missing or obscured markings, and visible panel damage.

• One control panel assembly (front user interface)

• Disconnect power to the appliance before beginning work to avoid shock.
• Remove outer trim or screws as needed; handle the display lens and ribbon cables gently to avoid damage.
• Keep small screws and clips organized during disassembly; reconnect all cables securely before reassembly.

This door gasket seals the refrigerator compartment to keep cold air in and reduce condensation. It replaces a worn or damaged seal to help maintain proper temperature and efficiency. What it does:

• Creates an airtight seal around the refrigerator door to minimize cold air loss
• Helps prevent frost buildup and moisture around the door opening
• Can reduce compressor run time by restoring a proper seal
• Common symptoms: visible gaps, torn or hardened gasket, persistent warm spots or excess frost

• Follow the appliance manufacturer's instructions and disconnect power before servicing
• Inspect mounting channel and clean surfaces before installing the new gasket
• Some gaskets require warming or stretching to seat correctly; replace carefully to avoid pinching

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening