Parts for Kitchenaid KUDR204KSB00: Lower Drawer Parts

This drawer box assembly replaces a damaged or worn storage drawer in the refrigerator, restoring proper storage capacity and smooth sliding operation. It provides a stable bin for fresh foods and helps keep produce organized. What it does:

• Replaces a cracked, warped, or broken refrigerator drawer to restore safe storage.
• Provides a rigid bin that supports food items and small containers.
• Restores smooth sliding and seating of the drawer when tracks and supports are intact.
• Helps prevent food from spilling into cabinet areas when functioning properly.

• Remove all food and contents before servicing; handle glass or plastic bins carefully to avoid damage.
• Follow the appliance owner's manual for drawer removal and reinstallation steps.
• Check drawer tracks and supports for damage; replace damaged hardware before installing the new drawer.
• Use gloves to protect hands from sharp edges and wipe the drawer clean before use.

This screw is a factory replacement fastener used to secure panels, trim, and internal components so parts stay aligned and appliances operate safely. It restores original fit where a missing or damaged screw causes loose panels or rattling. What it does:

• Secures cabinet panels, brackets, or trim pieces to restore solid fits
• Prevents vibration-related noise and movement caused by missing fasteners
• Replaces stripped or corroded screws that won't hold parts safely
• Matches OEM fastening points for correct installation when replacement is needed

• Use the correct screwdriver and size to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow appliance-specific safety steps before working on electric components
• Replace them as needed for full panel stability

This replacement mounting screw secures appliance panels and components so parts stay aligned and stable during use. A simple, direct fastener that restores proper fit and prevents rattling or loose trim. What it does

• Secures panels, brackets, or trim to the appliance frame
• Restores proper alignment and prevents vibration or rattling noises
• Keeps parts from shifting, reducing wear on connected components
• Works wherever the original screw was used to hold assemblies in place

• Disconnect power and/or water before accessing internal components
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for best fit

This replacement refrigerator door gasket creates the airtight seal around the fresh-food compartment to help maintain proper temperature and reduce energy loss. It restores a tight closing edge for better cooling performance and food preservation. What it does:

• Forms an airtight seal around the fresh-food door to keep cold air in and warm air out
• Helps reduce frost build-up and prevents moisture from entering the compartment
• Can improve cooling consistency and reduce excessive run-time or energy use
• Addresses common symptoms like a door that won't fully seal, warm spots, or visible gaps

• Remove the old gasket and clean the gasket channel thoroughly before installing the replacement
• Start at one corner and press the new gasket into the channel evenly; work around the door to seat all edges
• If needed, warm the gasket slightly to help it flex and form to the door frame
• Check the door seal after installation and adjust as needed; disconnect power before service if working near electrical components

This door gasket seals the refrigerator/freezer compartment to help maintain consistent internal temperatures and reduce moisture build-up. It replaces a worn or torn seal to help keep food fresher and minimize frost at the door. What it does:

• Creates an airtight seal between the door and cabinet to help maintain proper cooling
• Helps prevent warm air and moisture from entering the compartment
• Commonly replaced for symptoms like visible cracks, tears, gaps, or persistent frost buildup
• Can reduce excessive run-time caused by a failing door seal

• Disconnect power to the appliance before starting any repair
• Remove the old gasket by loosening the door trim or pulling it out of the retainer as applicable
• Press the new gasket evenly into the channel or reattach trim, ensuring full contact around the entire door edge
• Warm the gasket (hair dryer or warm water) if needed for flexibility and to improve final sealing; check for gaps after installation

This push plate is a replacement door push plate that restores a appliance's smooth, secure opening and closing action. It provides a durable touch surface where the door is pushed to open. What it does:

• Replaces a worn, cracked or broken push plate that prevents normal door operation
• Provides a solid contact point for opening the door without sticking or scraping
• Helps keep the underlying latch/door edge protected from wear
• Can improve the feel and alignment of the door when the original trim is damaged

• One push plate

• Basic, non-technical replacement; remove trim screws or clips to swap panels
• Disconnect power or secure the appliance per manufacturer safety guidance before working near electrical components
• Keep screws and small parts organized; use appropriate tools to avoid scratching finished surfaces
• If the door or latch shows additional damage, inspect related components before finishing the repair