Parts for Thermador PD366BS/02: Manifold Assy Parts

This pressure regulator controls and stabilizes incoming water pressure to the appliance, helping maintain consistent operation and protect internal valves and seals. Fits systems that use a 3/4 inch inlet regulator. What it does:

• Reduces high incoming water pressure to a safe, steady level for the appliance
• Prevents pressure-related leaks, valve chatter, and premature wear on seals
• Helps maintain consistent water flow for reliable cycles and operation
• Commonly replaced when irregular pressure, humming valves, or water leaks occur

• One pressure regulator (3/4 in.)

• Turn off water supply and power to the appliance before starting; relieve system pressure first
• Inspect connection fittings and seals; use appropriate thread sealant if required by the OEM
• Tighten to manufacturer torque recommendations and check for leaks after restoring water

This replacement tube restores proper routing for liquids or airflow in compatible appliances, helping maintain normal operation and prevent leaks or flow issues. It's a direct-fit part when your appliance requires the OEM tube. What it does:

• Replaces a worn, cracked, or damaged routing tube to stop leaks and restore proper flow
• Guides water, drain, or air where the original tubing was installed to maintain system function
• Helps prevent intermittent failures caused by pinched, split, or brittle tubing
• Matches OEM fit and routing to keep adjacent components aligned

• One replacement tube

• Verify the part number and orientation against the appliance diagram before installing
• Turn off power and water supply to the appliance before starting work
• Use appropriate tools and retainers; avoid kinking or over-bending the tube during installation

A 9-inch gas supply tube that routes fuel from the appliance inlet to the control valve/manifold, restoring proper gas delivery for safe, consistent burner operation when tubing is damaged or leaking. What it does:

• Channels gas to the control valve/manifold so burners can ignite and maintain a steady flame.
• Replaces bent, punctured, corroded, or leaking tubing that can interrupt fuel flow.
• Helps address common symptoms such as a gas odor near the appliance, burners that won't light, or low/uneven flames.
• OEM-style replacement designed for the corresponding Bosch gas appliance configurations.

• Shut off the gas supply and electrical power to the appliance before starting any work.
• Use correct fittings and approved thread sealant or gasketing; tighten to OEM-recommended torque if specified.
• After installation, perform a soap-and-water or approved leak test; if you detect a leak, shut off gas.

Replacement water inlet valve that controls an appliance's incoming water flow for reliable fill and cycle operation. Replacing a faulty valve can stop no-fill, slow-fill, or continuous-fill issues and restore normal performance. What it does:

• Opens and closes to regulate water entering the appliance during fill cycles.
• Helps ensure correct water levels for proper washing or rinsing.
• Common symptom fixer for appliances that won't fill, fill slowly, or keep filling.
• May cause visible leaks at the valve or trigger fill-related fault behavior if failed.

• Turn off power and shut off the water supply before starting any work.
• Open a cycle or relieve pressure to drain residual water before removing the old valve.
• Inspect and replace any worn seals or inlet hoses when installing the new valve.
• Follow the appliance service manual for specific removal/installation steps.

This replacement screw secures appliance panels and components in their proper position. Installing this screw restores a solid, factory fit and helps prevent vibration and misalignment.

• Fastens panels, brackets, or internal parts to the appliance chassis
• Maintains alignment to reduce vibration and rattling noises
• Replaces missing, rusty, or stripped hardware
• Typical symptoms include loose panels, gaps, rattles, or a screw that won't tighten

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Support panels and watch for sharp edges and pinch points
• Use the correct driver size/type for your model to avoid stripping
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing