Parts for Kenmore 417.71723512 (41771723512, 417 71723512): Motor / Tub Parts

This is a single replacement screw used to secure appliance panels and trim and restore proper fit. It provides a direct, no-frills fix when a missing or damaged fastener lets parts sit loose or rattle. What it does:

• Secures panels, brackets, trim pieces or small components to restore proper alignment
• Stops rattling or vibration caused by a missing or stripped fastener
• Replaces a lost or damaged screw to prevent gaps that collect dirt or cause wear

• Use the screw only where the OEM part specifies; fit before tightening
• Hand-start threads to avoid cross-threading, then tighten snugly—do not overtighten
• Disconnect power to the appliance before working near electrical components
• If threads are damaged or the mating part is stripped, replace the mating hardware

This washer agitator mounts in the tub of top-load models and creates the back-and-forth wash action that moves clothes through water and detergent. Replacing a cracked or loose agitator restores turnover and cleaning performance.

• Produces the oscillating motion that circulates clothes during the wash cycle
• Transfers drive from the shaft/hub to move laundry through water and detergent
• Restores proper load turnover for effective cleaning
• Can help resolve: washer not agitating, weak/slow agitation, poor cleaning, wobbly/noisy agitator, or visible cracks/broken fins

• Disconnect power and turn off water before servicing
• Remove the softener dispenser/cap and center bolt/retainer; lift out the old agitator
• Inspect and transfer any reusable cap or hardware to the new agitator
• Align and seat the new agitator on the drive hub; tighten the fastener per manufacturer guidance and test

This is a replacement motor-gear assembly kit from Frigidaire. It is designed to work in washer/dryer combo units and is responsible for turning the drum. The motor sits at the bottom of the part. It turns the spindle, and the splines ensure that the drum also turns. The motor assembly is a mechanical part and is subject to physical wear and tear. One common problem is the loss of grease/lubrication from the internal bearings over time. The splines on the spindle may also suffer from wear. When the motor fails, the washer/dryer unit will no longer function, and a replacement will be necessary. To replace the motor-gear assembly, first unplug the appliance. Remove the back to access the motor.This is a genuine OEM part. It's sold individually, and will fit Frigidaire and Electrolux washer/dryer combo units only.

This actuator motor drives the washer's brake and clutch to shift the mechanism between wash and spin. Replacing a worn actuator restores proper shifting so the tub agitates and spins at the right times and cycles can complete.

• Actuates the brake and clutch to change between agitation and spin modes
• Positions the shift mechanism via a small geared motor
• Helps the basket start/stop smoothly during cycle transitions
• Common failure symptoms: no spin, no agitate, stuck in one mode, or repeated clicking from the drive area

• Disconnect power before servicing; allow moving parts to stop completely
• Access the actuator near the drive/brake assembly (location varies by model)
• Note linkage and actuator orientation; remove screws and disconnect the harness, then install the new unit the same way
• Reassemble and run a spin and agitation test or your model's diagnostic check to verify shifting

This suspension rod stabilizes the washer tub during wash and spin, absorbing movement to reduce shaking and noise. Replacing a weakened rod restores proper balance and helps prevent banging, off-balance interruptions, and excess wear on other components.

• Supports and centers the tub within the cabinet
• Dampens vibration and tub oscillation during agitation and spin
• Helps prevent the tub from striking the cabinet
• Symptoms of a failing rod can include excessive vibration/shaking, loud banging, "walking," off-balance/UL errors, or wet loads after spin

• Disconnect power and water supply before servicing; wear gloves and eye protection
• Support the tub before removing the rod—spring tension is present
• Access from the top; release the upper retainer, then unhook the lower end from the tub mount
• Install in the same position/orientation as the original; replacing multiple rods together can help maintain balance

This replacement drain hose routes and removes defrost and condensation water so the fridge can drain properly and avoid pooling. It fits the factory drain path and restores normal water flow for proper operation. What it does

• Carries defrost and condensation water from the evaporator area to the drain or pan
• Stops water pooling inside the fresh-food compartment and under crisper drawers
• Prevents slow draining that can cause odors or potential water damage
• Works with existing clamps and routing channels when intact and properly installed

• Disconnect power to the appliance before starting and shut off any water supply if applicable
• Inspect hose routing and clamps, replace any damaged clamps or retainers for a secure fit
• Trim or route the hose as needed to match the original path without sharp bends or kinks
• After installation, restore power and check carefully for proper draining and leaks

This is a replacement screw used to secure appliance panels and components. It provides a direct-fit fastener to restore secure mounting and proper alignment of parts after repair. What it does:

• Secures panels, brackets, trim, or small components to the appliance frame
• Restores proper alignment and prevents rattling or loose parts
• Helps maintain safe, stable operation when used in the intended mounting location
• Works as a direct replacement for the original fastener when the correct PN is specified

• Use the matching screw hole and thread engagement; do not force or cross-thread
• Tighten to snug fit—avoid over-tightening which can strip threads or crack plastic
• If replacing multiple fasteners, use identical part numbers for consistent fit
• Disconnect power and follow appliance safety guidelines before accessing internal parts

This retaining ring secures internal components in place to help maintain proper alignment and reliable operation. Small, durable, and designed to fit specified Frigidaire assemblies where a snap/retaining ring is required. What it does

• Holds shafts, clips, or assemblies in position to prevent lateral movement or disassembly.
• Common replacement when parts shift, rattle, or come loose during use.
• Helps restore proper fit and reduces vibration-related noise.
• Used wherever a snap/retaining ring is specified by the manufacturer.

• One retaining ring as shown.

• Disconnect power and, if applicable, water supply before beginning repair.
• Use appropriate snap-ring or needle-nose pliers and eye protection when removing or installing small retaining rings.
• Verify correct orientation and seating in the groove to ensure secure retention.

This replacement cover restores a secure, protective barrier over a designated opening in your appliance's assembly. A properly fitted cover helps keep debris out and maintains designed performance when the original is cracked, warped, or missing. What it does:

• Shields internal components by closing and protecting an access or flow opening
• Helps maintain proper sealing and performance when correctly seated
• Replaces a broken, warped, or missing cover to restore a snug fit
• Common signs it's needed: visible damage, loose fit, rattling/vibration, or reduced performance around the covered area

• One cover

• Disconnect power and shut off water supply before servicing
• Note orientation and hardware locations; transfer any reusable screws/clips or seals
• Inspect mating surfaces; clean and replace any worn gasket/seal as needed
• After installation, run a short test and check for secure fit and abnormal noise

This replacement screw secures panels and small components on compatible Frigidaire appliances to restore a tight, rattle-free fit. Use it when factory screws are missing, stripped, or corroded to keep parts aligned and stable. What it does

• Fastens trim, panels, brackets or small assemblies to appliance cabinet or frame
• Helps stop rattling and vibration caused by loose or missing fasteners
• Maintains proper alignment of removable panels and components
• Provides the correct replacement hardware when original screws are damaged or corroded

• Turn power off or unplug the appliance before accessing internal parts.
• Match screw head style and length to the original before installation.
• Start threads by hand to avoid cross-threading; tighten securely but avoid overtightening.
• Keep small parts away from children and dispose of old/stripped fasteners properly.

This sensor monitors appliance conditions and relays a signal to the control so heating, cooling, or cycle functions occur at the right time. Replacing a failing sensor restores accurate feedback and more reliable operation.

• Detects operating conditions and sends signals to the control board
• Helps regulate heating/cooling output or cycle timing
• Common symptoms of a failed sensor: erratic operation, incorrect readings, cycles that won't start/finish, or related error codes
• Restores proper control feedback when the original is damaged or out of range

• Disconnect power to the appliance before servicing
• Access the sensor per your service manual; note wire colors/orientation and connector locks before removal
• Transfer any mounting clips or brackets from the original if required
• After installation, run diagnostics or verify resistance/continuity per the tech sheet to confirm proper operation

The Drain Hose Kit is an OEM part for Frigidaire washing machines. It includes all of the necessary tubing to safely drain used water away from the washer during each cycle. 

Causes of a bad drain hose kit can include cracks or splits from continuous bending fatigue, pinch points in drainage routing that compromise integrity over time, or dried-out rubber that becomes brittle and prone to leakage.

Symptoms of a failing kit include:

• Puddles of water accumulating near or under the washer
• Slow or incomplete draining after cycles have finished
• Water leaks at hose connections or along the length of tubing

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This hose/wire clamp secures appliance hoses or wiring to prevent rubbing, chafing and unwanted movement—helping reduce leaks, shorts, and noise from loose lines. Simple, small replacement that restores proper routing and retention. What it does:

• Holds a drain hose, water line or wiring bundle in place at attachment points
• Prevents hoses or wires from rubbing against sharp edges or moving parts
• Reduces risk of leaks, electrical chafing, rubbing noise, and vibration-related wear
• Fits into a mounting tab or hole and snaps or tightens to retain the line

• Disconnect power and shut off water before accessing plumbing or wiring
• Inspect nearby hoses/wires and mounting tabs; replace if damaged
• Position clamp over the hose or bundle and engage onto the mounting tab until secure
• Use appropriate pliers if needed; avoid over-tightening or deforming the hose

This seal restores a tight barrier between mating surfaces in your appliance, helping prevent leaks and performance loss. Replace a cracked, flattened, or torn seal to maintain proper containment of air or water and efficient operation.

• Forms a tight air- or water-resistant barrier where specified by the manufacturer
• Helps maintain proper temperatures, airflow, and/or water containment
• Wear or damage can lead to moisture leaks, condensation/frost, or longer run times
• Visible cracks, tears, gaps, or poor sealing are common indicators it's time to replace

• Disconnect power and shut off water before servicing
• Access the sealed area per your model's service manual and remove the old seal
• Clean mating surfaces; seat the new seal fully and evenly in its channel or onto the surface
• Test for proper sealing before returning to service

The Pump Assembly is an OEM component for Frigidaire washing machines. It is responsible for draining wash water from the washer tub at the end of each cycle before refilling with fresh water for rinses. 

Symptoms of a bad pump assembly include:

• Incomplete draining of water at the end of cycles  
• Standing or pooling water left in the bottom of the tub
• The washer fails to fill or refill with water properly
• Loud grinding or buzzing noises coming from the pump motor area

Causes of a bad pump assembly can be normal wear and tear over time, an obstructed drain line, or issues with the pump housing or impeller.

This genuine Frigidaire washer pump assembly restores efficient drainage and water circulation. This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This spring-style clamp secures hoses or tubing to fittings to help prevent leaks and reduce movement. It restores a tight connection for water or drain lines and helps stop rattling or hose separation during operation. What it does:

• Holds flexible hoses or tubing firmly on barbed fittings to prevent leaks
• Helps stabilize water and drain lines to reduce vibration and noise
• Keeps hose connections from slipping off during normal use
• Commonly replaced when clamps are corroded, stretched, or lose tension

• Disconnect power and shut off water supply before replacing hoses or clamps.
• Use pliers to expand the clamp, slide it into position, then release to secure; verify it sits fully over the fitting barb.
• Replace with the exact clamp size and type to ensure a proper seal; do not overtighten or cut the hose.
• If hose damage or leaks persist after replacing the clamp, inspect the hose and fitting and replace if necessary.

This ratchet-style fastener secures replaceable panels or components, keeping parts locked in place to prevent loosening and maintain proper alignment. Use it to restore secure fastening and reduce vibration or rattling. What it does:

• Holds panels or components with a one-way ratcheting grip to prevent back-out
• Restores secure attachment when original fastener is worn or stripped
• Helps stop panel rattling, vibration noise, or intermittent gaps
• Works where a small, durable locking fastener is required

• Disconnect power and unplug the appliance before starting any repair
• Use appropriate hand tools; avoid overtightening which can strip threads
• Inspect mating holes and surrounding fasteners; replace any damaged parts
• Test fit and operation after installation to ensure secure engagement

This replacement screw fastens appliance panels and components to restore secure fit and reduce movement. It's a direct-fit fastener used where the original mounting screw has become stripped, lost, or damaged. What it does:

• Secures panels, brackets, trim, or small internal components in place
• Stops rattling and vibration caused by loose fasteners
• Replaces a missing or damaged mounting screw to restore proper alignment
• Works where the original factory screw was used for fastening

• Use the correct screwdriver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to threads or sheet metal
• Disconnect power before working near live electrical components or heating elements
• Keep removed screws organized to ensure correct reinstallation

A simple wire-fastening cable tie that secures wiring and small hoses to prevent rubbing, snagging, or loose routing inside the appliance. Helps keep components organized for safer, quieter operation. What it does

• Secures wiring bundles and small hoses to chassis or brackets to prevent abrasion and movement
• Helps stop intermittent shorts or electrical noise caused by wires rubbing or contacting other parts
• Keeps airflow and moving parts clear by holding wiring away from fans and belts
• Useful when replacing or re-routing harnesses during repairs

• Always disconnect power before working on the appliance.
• Loop tie around wiring or hose, pull to secure snugly, and trim excess tail; do not overtighten.
• Replace ties that are brittle or damaged; use the same routing as the original harness.
• Dispose of trimmed ends and avoid sharp edges that could cut wiring insulation.

No.8 pan head `10 - 10b x 0.50 `cr/sq drive