Parts for Frigidaire FGMO3067UD: Oven / Cabinet Parts

The Magnetron is an OEM part for Frigidaire microwaves. It is responsible for generating the microwave energy that heats and cooks your food quickly and efficiently. It converts electrical energy which is then distributed throughout the microwave cavity.

A bad magnetron can be caused by electrical issues, component failure, or physical damage. Signs of a faulty magnetron include the microwave not heating food properly, unusual noises during operation, or complete failure to produce heat.

Symptoms of a bad magnetron include:

• Microwave not heating 
• Unusual buzzing or humming noises
• Failure to produce heat or power

Replace your defective or damaged microwave magnetron with this genuine OEM Frigidaire part to restore your microwave. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This control transformer supplies the low-voltage power needed for the refrigerator's control and electronic components, restoring reliable control circuit operation when the original transformer fails. What it does:

• Steps down incoming line voltage to the low-voltage level used by control boards and relays
• Replaces a failed or noisy transformer that can cause control malfunctions or intermittent operation
• Helps restore power to electronic controls, ice/water solenoids, and other low-voltage components
• Fits systems that use this exact OEM transformer part number

• One control transformer

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle wiring carefully; match wire colors/terminals and secure connections per wiring diagram
• Inspect related wiring and connectors for damage; replace any worn components

This replacement capacitor helps the refrigerator's motor start and run more reliably, restoring normal cooling operation and reducing hard-start symptoms. It's a direct-fit component used in compatible Frigidaire refrigeration systems. What it does:

• Provides the electrical pulse needed for the compressor/condenser motor to start and maintain stable operation
• Helps prevent slow or failed starts that can cause warm temperatures or compressor strain
• Can reduce excessive motor humming or cycling tied to a failing capacitor
• Supports overall cooling performance when the original capacitor is weak or faulty

• Capacitor as shown

• Disconnect power to the appliance before accessing electrical components
• Handle and connect terminals carefully to avoid short circuits; observe polarity/terminal labeling if present
• Dispose of the old capacitor per local electronic waste regulations

Replacement electrical diode for Frigidaire refrigerators that directs current flow to protect control circuitry and help defrost and compressor systems operate correctly. Installs quickly to restore proper electrical function when a diode fails. What it does:

• Allows electrical current to flow in only one direction to protect sensitive control and compressor circuits.
• Prevents backfeed that can damage control boards or other components.
• Common symptom: intermittent or no compressor/defrost operation.
• Other symptoms: blown fuses, tripped breakers, or erratic electrical behavior in the appliance.

• Disconnect power to the appliance before beginning any service.
• Handle electrical connections carefully; use insulated tools and avoid touching live terminals.
• Confirm connector fit and orientation before finalizing installation.

This replacement refrigerator water filter cartridge helps restore clean tasting water and ice by trapping common impurities. Designed as a direct-fit replacement to maintain your fridge's filtered water supply and improve taste clarity. What it does:

• Filters particulates and common contaminants to improve water and ice taste
• Helps reduce visible sediment and cloudiness from the dispenser and ice maker
• Restores normal dispensing performance when an old filter causes off-flavors or odors
• Supports consistent filtered water flow when installed and maintained

• Turn off the water supply and follow the refrigerator's filter-replacement instructions before starting
• Push/rotate or slide per your model's procedure until the filter locks in place; ensure a secure seal
• Run water through the dispenser for a short time after installation to flush air and initial carbon fines
• Replace regularly per the refrigerator manufacturer's recommendation or sooner if flow decreases or taste returns

This thermal fuse is a safety device that interrupts the defrost circuit when temperatures get too high, protecting the refrigerator from overheating and preventing damage to the wiring and components. What it does:

• Opens the defrost circuit if the evaporator area overheats to stop further heating and reduce fire risk
• Prevents the defrost heater from running when temperatures exceed safe limits
• Common symptom of failure: evaporator stays frosted and refrigerator cooling performance worsens
• Another symptom: defrost system never runs even though the timer or control calls for a defrost cycle

• Always disconnect power to the appliance before testing or replacing the fuse
• Locate the fuse on or near the evaporator/defrost heater assembly; exact location for your model
• Use proper insulation and connectors; do not bypass the fuse or use unapproved substitutes
• If the fuse failed, inspect the defrost heater, thermostat, and wiring for faults before reinstalling

This temperature sensor monitors internal fridge/freezer temperature so the control board can regulate cooling and defrost cycles for more consistent temperatures and food safety. What it does

• Measures compartment temperature and sends readings to the control board.
• Helps the refrigerator maintain set temperatures by enabling accurate cooling cycles.
• Supports proper defrost control when used in defrost/evaporator applications.
• A failing sensor can produce temperature fluctuation, poor cooling, or longer run times.

• One temperature sensor

• Disconnect power before servicing to avoid shock or compressor damage.
• Handle the sensor and connector gently; avoid pulling on wires.
• Verify location and routing match the original; secure sensor to prevent contact with moving parts.

This fuse assembly is the OEM replacement thermal cut-out that restores the appliance's built-in overheat protection and electrical safety. Replacing a failed fuse assembly helps return safe, reliable operation. What it does

• Acts as a thermal cut-out / fuse to interrupt power if internal temperatures exceed safe limits
• Prevents overheating that can damage components or create a fire hazard
• Stops electrical operation when the fuse is blown so a fault is isolated
• Common symptom: appliance will not power on, will not heat, or stops running intermittently

• One fuse assembly

• Disconnect power (unplug or shut off breaker) before beginning any service
• Handle the fuse and wiring carefully; replace only with the exact part number
• Basic hand tools are typically required; avoid pinching or over-bending wires during install

This thermostat is a temperature-sensing switch used in select appliances to control operation or provide over-temperature protection. It opens or closes the circuit at a calibrated point to help maintain proper, consistent performance. What it does

• Senses temperature at its mounting/location and switches contacts at a set point
• Regulates cycling of the system or ends a heating/cooling/defrost event as designed
• Helps prevent overheating or overcooling conditions and protects components
• Supports stable, reliable operation when the original thermostat fails

• Runs continuously or won't cycle off
• Shuts off too soon or won't turn on
• Inconsistent temperature (too warm/too cold)
• Erratic cycling or failure to maintain set temperature

• 1 thermostat

• Disconnect power before servicing; allow any hot surfaces to cool
• Note wire positions; move leads one at a time to the new thermostat
• Mount in the original location and orientation; ensure firm contact/fit
• Route any sensing bulb/capillary exactly like the original; avoid kinks

This temperature control thermostat regulates the refrigerator's cooling system to maintain set temperatures and restore proper food storage conditions. It replaces a faulty control that won't cycle the compressor correctly. What it does

• Senses cabinet temperature and switches the compressor on and off to maintain the selected setting.
• Restores normal cycling when a failed thermostat causes constant running or no cooling.
• Works with the control housing and capillary tube to respond to temperature changes.
• Compatible with common refrigerator control panels that use a mechanical capillary thermostat.

• One temperature control thermostat.

• Disconnect power to the appliance before starting any repair.
• Access usually requires removing the control panel or adapter; handle the capillary tube carefully to avoid kinks.
• Verify proper operation after installation by cycling through temperature settings and monitoring compressor response.

This electronic PC board controls a refrigerator's major functions, translating user inputs and sensor signals into compressor, fan, and defrost actions to keep the appliance operating correctly. Replacing a failed board restores control communication and timing. What it does

• Manages compressor, evaporator fan, and defrost cycle commands based on sensor inputs
• Receives user control panel inputs and runs display/indicator signals
• Monitors temperature sensors and timing to maintain cooling cycles
• Faulty board can cause no display, no cooling, intermittent operation, or error codes

• Disconnect power before servicing to avoid shock or damage
• Handle the board by edges and avoid static discharge; use an anti-static wrist strap if available
• Verify connector orientation and seating; do not force connectors

This replacement shield plate protects internal oven components from direct heat and helps maintain proper airflow for even cooking. It restores the original barrier that prevents heat damage and reduces hot spots inside the cavity. What it does:

• Deflects and disperses heat away from nearby wiring, sensors, and insulation
• Helps maintain consistent oven temperatures by preventing localized hot spots
• Reduces risk of heat-related component damage and premature wear
• Can stop heat-related smells or visible scorching when the original shield is damaged or missing

• Disconnect power to the appliance before starting any repair.
• Use gloves to avoid cuts from sharp edges and take care not to damage surrounding insulation or wiring.
• Verify correct orientation and secure with the original fasteners; do not force or modify the part.

This is a factory electrical switch that opens and closes a circuit to control a specific function in your appliance. Replacing a worn switch restores reliable on/off control and can resolve unresponsive or intermittent operation. What it does:

• Opens/closes the circuit to send power or signal to the assigned component
• Helps correct no response, intermittent function, or a component stuck on/off
• Addresses issues from worn contacts, loose/broken actuator, or heat-damaged terminals
• Model-specific design; match terminal layout and actuator style to the original

• One switch

• Disconnect power (unplug or switch off the breaker) before servicing
• Access the switch and label or photograph wiring for reference
• Transfer wires one at a time to matching terminals; secure the switch in place
• Restore power and test operation before reassembly

This replacement switch controls power to a specific function on your appliance. When a switch wears out, that feature may not turn on or off or may work intermittently. Replacing it restores reliable operation and control.

• Directs electrical power to the selected component or feature
• Actuates when the user presses a button, turns a knob, or flips a lever
• Common symptoms: no response from the selected function, intermittent operation, or a loose/broken actuator
• Visual signs can include heat discoloration on terminals or a burnt odor
• Can be checked with a multimeter for proper continuity when actuated

• Disconnect power to the appliance before service (unplug or switch off the circuit breaker)
• Access the switch per your model's service/owner documentation; take a photo of wire routing
• Transfer wires to the new switch one at a time to match positions and orientation; secure mounting hardware
• Restore power and test the function controlled by the switch

The Latch Board is an OEM part for Frigidaire microwaves. It controls the latch mechanism, allowing you to securely close and open the microwave door. It works with the door latch to ensure that the microwave door is securely closed during operation.

A bad latch board can be caused by electrical issues, component failure, or physical damage. Signs of a faulty latch board include the microwave door not closing properly, difficulty in opening or closing the door, or error messages displayed on the control panel.

Symptoms of a bad latch board include:

• The microwave door not closing or latching
• Difficulty in opening or closing the door
• Error messages related to the door latch

Replace your faulty or damaged latch board with this genuine OEM Frigidaire part to restore your microwave. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Latch Board is an OEM part for Frigidaire microwaves. It controls the latch mechanism, allowing you to securely close and open the microwave door. It works with the door latch to ensure that the microwave door is securely closed during operation.

A bad latch board can be caused by electrical issues, component failure, or physical damage. Signs of a faulty latch board include the microwave door not closing properly, difficulty in opening or closing the door, or error messages displayed on the control panel.

Symptoms of a bad latch board include:

• The microwave door not closing or latching
• Difficulty in opening or closing the door
• Error messages related to the door latch

Replace your faulty or damaged latch board with this genuine OEM Frigidaire part to restore your microwave. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This metal support rod replaces a worn or damaged mounting rod to restore proper alignment and secure attachment of the related component. A simple, direct replacement when the original rod is bent, broken, or missing. What it does:

• Provides structural support and alignment for the appliance component it mounts
• Keeps moving parts guided so doors, panels or assemblies operate smoothly
• Stops excessive play, rattling or misalignment caused by a bent or broken rod
• Reinstates reliable attachment after hardware wear or accidental damage

• One replacement rod

• Disconnect power before beginning any repair and work on a cool, dry appliance
• Inspect surrounding clips, bushings or brackets and replace if worn to ensure proper fit
• Use basic hand tools; avoid forcing or bending the new rod during installation
• Follow the OEM diagram for correct routing and fastening

The Rotating Ring is an OEM part for Frigidaire microwaves. It supports and rotates the glass tray during the cooking process for even heating of your food.

A bad rotating ring can be caused by wear and tear, damage, or improper alignment. Signs of a faulty rotating ring include the glass tray not rotating or turning unevenly, strange noises during operation, or the tray falling off the ring.

Symptoms of a bad rotating ring can include:

• The glass tray not rotating
• Noises during operation
• The tray not fitting securely in place

Replace your damaged or malfunctioning rotating ring with this genuine OEM part to restore your microwave. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Glass Turntable Plate is an OEM part for Frigidaire microwaves. As the surface food rests upon during cooking, it features heat-resistant tempered glass construction suitable for high-power microwave usage. 

Causes of damage can include cracking or splitting from thermal shock of sudden temperature changes during repeated heating and cooling cycles. Improper cleaning methods using harsh chemicals may also degrade protective coatings.

Symptoms of a faulty glass plate involve: 

• Cracks or chips exposing sharp edges presenting a hazard
• Denting or warping preventing level rotation inside the cavity
• Staining or clouding compromising visibility of cooking foods

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models.

This mounting bracket secures internal appliance components for stable operation and correct alignment. It replaces a worn or damaged bracket to restore proper support and reduce noise or shifting of the attached part. What it does

• Provides a sturdy mounting point for internal components to keep them aligned and secure
• Helps eliminate rattling, vibration, or misalignment caused by a broken or bent bracket
• Restores correct spacing so connected parts operate smoothly
• Used where a fixed support or attachment point is required inside the appliance

• Inspect surrounding parts and hardware; replace any stripped or damaged screws for secure installation
• Disconnect power to the appliance before accessing internal areas
• Install using the original mounting location and hardware; verify bracket orientation matches OEM placement
• If holes or fasteners do not line up, do not force parts—re-check part number and fit

This air duct directs cold air from the evaporator into the refrigerator/freezer compartment to help maintain even temperatures and proper airflow. It replaces a cracked or broken duct that can disrupt circulation and cooling. What it does:

• Channels cold air from the evaporator to the cabinet for more consistent cooling.
• Helps prevent uneven temperatures and warm spots by guiding airflow.
• Can reduce frost or ice buildup caused by turbulent or obstructed airflow.
• Commonly replaced when cracked, warped, or missing and airflow is reduced.

• Unplug the appliance or disconnect power before starting any repair.
• Installation typically requires removing interior panels or the evaporator cover; keep fasteners organized.
• Handle the duct and nearby evaporator components carefully to avoid damage.

This replacement holder is a molded mounting bracket that secures internal refrigerator components so they stay aligned and stable for reliable operation. It restores proper fitment and prevents loose or misaligned parts from shifting. What it does:

• Provides a secure mounting point for an internal refrigerator component to keep it properly positioned
• Stops rattling, shifting, or sagging caused by a broken or worn holder
• Helps restore proper alignment that can affect door/compartment fit or component operation
• Matches OEM fit and mounting points for a straightforward swap

• One replacement holder/mounting bracket

• Disconnect power before starting any repair to avoid shock or damage
• Remove shelves or panels as needed to access the damaged holder
• Most installs use snaps or simple fasteners; avoid forcing parts to prevent breakage
• If screws or clips are used, retain hardware and replace only what is explicitly required

This outer case is the main cabinet that surrounds and protects the appliance's internal components while restoring the unit's appearance. It replaces a damaged, dented, or corroded cabinet to help keep innards secure and reduce noise. What it does:

• Encloses and protects internal parts from dust, debris, and accidental contact
• Restores cosmetic appearance when original cabinet is dented, scratched, or rusted
• Helps reduce vibration and rattling by providing a stable outer structure
• Maintains proper airflow and alignment of panels for safe operation

• Disconnect power (and water if applicable) before beginning any repair
• This part may require removing panels and disconnecting trim; follow factory service instructions
• Two people may be needed to handle and position the cabinet safely