Parts for Kenmore 721.85032011 (72185032011, 721 85032011): Oven Cavity Parts

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This replacement mounting screw secures panels and small appliance components to restore proper fit and prevent vibration or loose parts. A simple, direct replacement when the original fastener is missing or damaged. What it does:

• Secures panels, brackets, or small assemblies to keep parts aligned
• Stops rattling or vibration caused by loose or missing screws
• Restores normal fit where a stripped or corroded screw failed
• Matches the OEM fastener form for a correct, long-lasting fit

• Unplug the appliance or disconnect power before servicing
• Use the correct driver to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or housing

This replacement door glass restores a clear viewing window and the protective barrier on your microwave door. Replace it when the original panel is cracked, shattered, or heavily scratched to keep the door secure and safe to use.

• Provides the see-through window and protective barrier within the microwave door
• Helps maintain proper door rigidity and alignment when intact
• Replace if the glass is cracked, chipped, shattered, loose, or badly scratched
• Reduced visibility, rattling, or visible damage are common symptoms of failure

• Unplug the microwave before servicing; microwaves can retain high voltage—use caution and do not open the cabinet
• Support the door; removal from the hinges may be required per your model's diagram
• Handle glass with cut-resistant gloves; edges can be sharp
• Transfer any reusable trim/clips as directed and verify the door latches and closes properly after installation

The Grille and Vent Assembly is an OEM replacement part for LG countertop microwave models. Located on the exterior rear casing, it protects interior electronics while maintaining cooling air circulation.

Causes of a bad grille involve warping or rust accumulating from steam ventilation, obstructing necessary exhaust. Reliable microwave operation requires durable venting.

Symptoms include:

• Overheating causing error codes or safety shutoffs to engage
• Reduced cooking consistency from compromised thermal regulation
• Visible damage presenting an unattractive appearance

This genuine LG replacement is compatible also with select Kenmore/Sears models.

The Light Bulb is an OEM part for LG microwaves. It provides illumination inside the microwave oven, allowing users to monitor the cooking process and check the condition of the food without opening the door.

Causes of a bad light bulb can include normal wear and tear, electrical surges, or damage due to impact or overheating. Over time, the filament inside the bulb can burn out, or the bulb itself can become loose or disconnected.

Symptoms of a bad light bulb include:

• The microwave interior light not turning on
• Flickering or dimming of the light
• Intermittent lighting during operation

This OEM LG part is also compatible with Sears/Kenmore models.

This replacement lamp socket holds the light bulb and provides a stable electrical connection so your appliance light works reliably. Replace a heat-damaged or loose socket to restore consistent illumination and help prevent flicker, arcing, and premature bulb failure.

• Secures the bulb and connects it to power
• Restores proper interior or work-area lighting
• Addresses flickering, intermittent light, or bulbs failing early from poor contact
• Replaces sockets that are cracked, melted, or discolored

• Disconnect power at the breaker or unplug before servicing
• Allow the area to cool; wear gloves and safety glasses
• Note wire positions and transfer one lead at a time to the new socket
• If servicing a microwave, access only the lamp area per your model instructions; do not open the cabinet—internal components can retain high voltage