Parts for Kenmore 721.85033111 (72185033111, 721 85033111): Oven Cavity Parts

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This factory fastener secures appliance panels and components. Use it to replace a missing, stripped, or corroded screw so brackets, covers, and assemblies stay tight and properly aligned, helping reduce vibration and rattling.

• Secures panels, brackets, and internal components in their proper positions
• Replaces missing, worn, or cross-threaded hardware
• Helps eliminate vibration and rattling from loose parts
• Supports proper alignment of covers and assemblies

• Disconnect power to the appliance before servicing; allow any moving parts to stop
• Match this screw to the location shown in your model's parts diagram
• Start threads by hand to avoid cross-threading, then tighten snugly with the correct driver
• Do not overtighten to prevent stripping threads or cracking plastic bosses

The Grille, Vent is an OEM part for LG microwaves. The grille measures approximately 23 x 3.75 inches and is designed to cover components inside your microwave. Positioned typically at the top or front of the microwave, this grille ensures that the appliance maintains an optimal temperature, preventing overheating and ensuring efficient operation.

Symptoms of a failing Vent Grille include:

• Excessive steam or heat buildup within the microwave
• The microwave overheating during use
• Noise or vibration due to loose or damaged grille components
• Visible signs of wear, such as cracks, warping, or discoloration on the grille

Causes of a bad vent grille can include physical damage from routine cleaning or use, warping due to exposure to high temperatures, or blockages from accumulated grease and debris which can restrict airflow.

Size: 5 inches x 7 3/4 inches.

The Light Bulb is an OEM part for LG microwaves. It provides illumination inside the microwave oven, allowing users to monitor the cooking process and check the condition of the food without opening the door.

Causes of a bad light bulb can include normal wear and tear, electrical surges, or damage due to impact or overheating. Over time, the filament inside the bulb can burn out, or the bulb itself can become loose or disconnected.

Symptoms of a bad light bulb include:

• The microwave interior light not turning on
• Flickering or dimming of the light
• Intermittent lighting during operation

This OEM LG part is also compatible with Sears/Kenmore models.

This bracket assembly provides a secure mounting point for internal components, keeping parts aligned and stable for reliable appliance operation. It restores proper support where a worn or broken bracket causes rattling or misalignment. What it does:

• Secures and supports internal components or panels to prevent movement and vibration
• Restores proper alignment for parts that have shifted due to a damaged bracket
• Helps eliminate rattling, knocking, or loose-panel noises caused by broken mounting points
• Maintains spacing that ensures connected parts operate smoothly

• Disconnect power before beginning any repair to avoid electrical shock
• Inspect surrounding fasteners and mounting surfaces; replace any stripped screws or damaged clips
• Use appropriate hand tools; avoid over-tightening fasteners which can crack plastic parts

This replacement lamp socket holds the light bulb and provides a stable electrical connection so your appliance light works reliably. Replace a heat-damaged or loose socket to restore consistent illumination and help prevent flicker, arcing, and premature bulb failure.

• Secures the bulb and connects it to power
• Restores proper interior or work-area lighting
• Addresses flickering, intermittent light, or bulbs failing early from poor contact
• Replaces sockets that are cracked, melted, or discolored

• Disconnect power at the breaker or unplug before servicing
• Allow the area to cool; wear gloves and safety glasses
• Note wire positions and transfer one lead at a time to the new socket
• If servicing a microwave, access only the lamp area per your model instructions; do not open the cabinet—internal components can retain high voltage