Parts for Kitchenaid KEBS208SBL02: 03 - Oven Door Parts

This door glass is the clear panel in the appliance door that restores visibility and door integrity when the original glass is cracked, shattered, or damaged. Replacing it restores a safe, clean viewing window.

• Replaces a broken or cloudy door glass panel to restore a clear view into the interior
• Helps maintain proper door integrity and safe operation after damage
• Common symptoms: cracks, chips, spiderwebbing, shattered glass, or loose/rattling fragments
• Cosmetic damage inside the window area that cannot be cleaned away

What's included: One door glass panel Install notes:

• Disconnect power; for gas units shut off gas, and for water-using appliances shut off water before service
• Wear cut-resistant gloves and eye protection; handle glass by the edges only
• Support or remove the door per service instructions; transfer original trim, brackets, and screws to the new glass
• After reassembly, verify door alignment, latch operation, and seal

This 10-32 x 3/8 machine screw secures appliance components. It keeps panels, brackets, and trim firmly attached so everything stays aligned and quiet during operation.

• Fastens metal parts using a 10-32 thread in pre-tapped holes or with a matching 10-32 nut
• Maintains proper alignment of panels, brackets, and trim to reduce vibration and rattling
• Replace if the original screw is missing, stripped, rusted, or damaged
• Using the correct hardware helps restore a secure, factory-tight fit

• Disconnect power; shut off gas supply if applicable. Allow the appliance to cool completely before servicing
• Note screw locations/lengths and replace like-for-like
• Start threads by hand to avoid cross-threading; snug with the appropriate driver—do not overtighten
• If the receiving threads are damaged, repair or replace the mating component before installing

This ground screw secures the appliance's grounding wire or strap to the chassis or terminal area, creating a reliable bonding point. Replace a missing or damaged screw to restore a proper ground connection during installation or service.

• Provides the designated bonding point for the grounding wire/strap
• Fastens to the frame or terminal area using 8-32 machine threads
• Helps maintain a consistent ground path for safe operation
• Typical reasons to replace: stripped head/threads, corrosion, or a missing screw

• Disconnect power at the breaker or unplug the appliance before servicing
• Route the ground wire/strap to the specified grounding location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Ensure the ground connection is secure and complies with local electrical codes before restoring power

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement seal restores a tight barrier between mating components, helping prevent leaks and maintain proper performance. Install it when the original seal becomes worn or damaged to keep moisture and fluids contained where they belong. What it does

• Creates a watertight/airtight seal between connected parts
• Helps prevent drips, seepage, and moisture escaping from joints
• Maintains correct system pressure/flow at the sealed connection
• Replace if the old seal is cracked, flattened, swollen, or brittle
• Common symptoms include moisture around the joint, intermittent leaks, or residue/mineral trails

• 1 seal

• Disconnect power and, if applicable, shut off water supply before service
• Remove the old seal and clean the groove and mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved silicone grease only; seat the seal evenly without twisting
• Reassemble, restore utilities, and run a short test to check for leaks

This seal restores a tight barrier between two mating parts in your appliance to prevent leaks and contamination. Replacing a worn or cracked seal helps stop drips, drafts, and noise so the unit can run reliably.

• Forms a tight seal between components to contain fluids or air
• Helps prevent leaks, drips, condensation, or unwanted airflow at joints
• Maintains efficient performance and reduces noise or vibration from loose fits
• Common failure signs: visible cracks/flattening, moisture where parts meet, odors, or louder operation

• Disconnect power and shut off water before servicing
• Note the seal's orientation; remove the old seal and clean all mating surfaces
• Install without stretching; lightly moisten if specified by your service manual (avoid petroleum products unless directed)
• Reassemble and test for proper operation and any leaks