Kenmore Ice Maker 106.89582705 (10689582705, 106 89582705) Parts

The  Drain Pump Assembly is an OEM part for Whirlpool ice machines. It removes melted water from the harvest and storage bin to allow continuous ice production. This pump assembly contains the electric drain pump motor and impeller which work together to discharge drain water through the outlet hose.

Causes of a bad drain pump assembly can include wear due to heavy use over time, a buildup of mineral deposits or other debris clogging the impeller, or failure of the motor itself.

Symptoms of a bad drain pump assembly include:

• Standing water in the storage bin
• Inability to harvest or store ice
• Strange noises or vibrations coming from the pump area
• Leaks from around the pump housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This condenser fan blade moves air across the refrigerator's condenser coil and compressor to remove heat, helping the unit cool efficiently. Replace a cracked, warped, or loose blade to restore proper airflow and reduce noise.

• Circulates air through the condenser section to dissipate heat from the refrigerant
• Supports stable fridge and freezer temperatures and efficient compressor operation
• Common symptoms: rattling/scraping noises, weak or no airflow at the rear/bottom, longer run times, or warming compartments
• Replace if the blade is cracked, warped, wobbling, or loose on the motor shaft

• Disconnect power and pull the refrigerator away from the wall; remove the rear access panel to reach the condenser fan
• Note the original blade orientation/rotation; remove the old blade from the motor shaft (release any retainer if present)
• Press the new blade onto the shaft until fully seated; ensure it spins freely with proper clearance and airflow direction
• Reinstall the panel, restore power, and verify normal airflow and sound

This replacement water line hose restores a secure water connection to your appliance, helping stop leaks and restore proper dispenser or ice maker water flow. Designed to match factory fit and routing for an exact replacement. What it does

• Carries water between the household water supply and the appliance water inlet or dispenser.
• Restores normal water flow to the ice maker or dispenser when a damaged hose is causing low or no water delivery.
• Prevents leaks and pooling when the original hose is cracked, split, or worn.
• Provides a flexible, durable connection that resists kinking when installed correctly.

• One replacement water line hose.

• Turn off the water supply and unplug the appliance before starting; relieve any residual water pressure by operating the dispenser briefly.
• Inspect fittings and valves for wear; replace clamps or gaskets if they show damage to ensure a watertight seal.
• After installation, turn the water back on slowly, check all connections for leaks, and run the dispenser/ice maker to verify proper flow.

Size: 8-32 x 1/2 inch.

This wire harness connects the ice maker's cutter grid to the appliance's electrical system, supplying power so the heated grid can slice the ice slab into cubes. Replacing a damaged harness helps restore consistent cube separation and production.

• Routes electrical power to the cutter grid/heating wires
• A failed, loose, or heat-damaged harness may prevent the grid from warming
• Common symptoms may include whole sheets or large chunks in the bin, cubes not separating, or intermittent/slow ice production
• Visual signs can include melted/discolored grid connectors or broken/brittle conductors

• Disconnect power before servicing; allow the cutter grid to cool completely
• Note wiring/connector orientation; transfer one connection at a time to match original routing
• Seat connectors fully and secure the harness in original clips/standoffs away from sharp edges
• After reassembly, restore power and verify the cutter grid warms during a cycle

This front-and-rear mounting bracket secures the appliance's front and rear assemblies to the cabinet, restoring proper alignment and support. Replacing a worn or damaged bracket helps reduce panel movement, rattling and improper fit. What it does:

• Provides a stable mounting point for the appliance's front and rear assemblies to maintain alignment and cabinet integrity.
• Stops or reduces rattling, vibration and shifting caused by loose or broken mounting hardware.
• Prevents gaps and misalignment that can affect doors, panels or controls.
• Fits original mounting locations to restore factory support.

• Bracket (front and rear)

• Disconnect power (and water if applicable) before starting any repair.
• Use the original fasteners or manufacturer-recommended hardware; do not force or bend the bracket.
• Inspect adjacent mounting points and fasteners for wear; replace any damaged parts.

This is a replacement left/right mounting bracket used to secure interior panels or trim and restore proper alignment and fit. It provides a simple fix for loose panels and misalignment without replacing larger assemblies. What it does:

• Secures an interior panel, trim piece, or rail to the appliance cabinet
• Restores proper alignment to reduce rubbing or binding of doors or panels
• Prevents rattling or movement caused by worn or broken brackets
• Helps maintain correct spacing for connected components

• Basic hand tools typically required; refer to your appliance's service manual for the exact procedure
• Disconnect power (and gas if applicable) before beginning any repair to avoid shock or injury
• Keep removed fasteners and parts organized for reassembly; replace any damaged screws

This catch assembly secures the appliance door in the closed position, restoring proper latching and preventing unwanted openings. It's a direct-fit replacement designed to match the original OEM function. What it does

• Holds the door closed so seals stay engaged and the appliance maintains internal temperature
• Prevents the door from popping open or rattling during operation or transit
• Helps stop issues like airflow loss, frequent door alarms, or intermittent cycling caused by a loose latch
• Matches OEM fit and mounting points for straightforward replacement

• One catch assembly

• Disconnect power (and water if applicable) before starting any repair
• Remove the door panel or trim required to access the existing catch; keep screws and fasteners organized
• Compare the new part to the old part before installation to ensure fit and orientation
• After installation, cycle the door several times to ensure secure engagement and proper alignment