Kenmore Washer 110.20932990 (11020932990, 110 20932990) Parts

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Size: 10-16 x 5/8 inch.

Almond. Size: 13 oz. can. Acrylic appliance paint.

This driven cam bearing supports the cam in the compactor's drive assembly, reducing friction and keeping components aligned so the ram moves smoothly and the unit completes and reverses cycles reliably.

• Supports and centers the driven cam/gear for proper alignment
• Reduces friction and wear for smoother cam rotation
• Helps ensure correct switch timing so the ram reverses at end of travel
• Symptoms of wear include squealing/grinding, binding or jerky ram movement, or failure to complete a cycle

• Disconnect power at the breaker or unplug the unit before servicing
• Secure the drawer/ram to prevent unintended movement while working
• Access the drive mechanism and note the bearing's orientation on the cam before removal
• Seat the new bearing fully and hand-rotate the cam to verify smooth movement before reassembly and restoring power

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Size: 21 inches long. Clamp included.

Includes drive tube spacer, "T" bearing and both shaft seals.

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation

Used from harness to top.

2 position. Extra rinse.

Color: Almond

This trim piece finishes and protects an opening or edge on your appliance's cabinet or console. Replacing a cracked or missing trim restores a clean, factory look and helps nearby components sit and operate as intended. What it does:

• Provides a clean, finished edge and covers sharp cabinet/console edges
• Helps keep adjacent parts aligned and secured around the opening
• Restores appearance when original trim is cracked, warped, discolored, or missing
• Common symptoms: loose or rattling piece, cosmetic damage, snagging edges, or poor fit of nearby parts

• 1 trim piece

• Disconnect power; if applicable, shut off gas or water. Wear cut-resistant gloves.
• Remove the existing trim by releasing clips or removing screws; note orientation and retain hardware.
• Transfer any reusable clips/inserts from the old trim to the new part.
• Align and snap/screw the new trim into place; do not overtighten.

Size: .20 Fl. Oz. (6 ml)

This cam-agitator is the replacement cam that guides the agitator's motion in compatible top-load washing machines, restoring proper agitation and helping the washer move clothes through the wash cycle effectively. What it does:

• Replaces the worn or broken agitator cam that controls the agitator's directional movement.
• Helps restore normal agitation when the agitator slips, spins freely, or fails to shift between wash and spin.
• Works with the agitator assembly to transfer drive action from the transmission to the agitator.
• Designed to fit and align with the agitator and related fasteners for reliable operation.

• Basic mechanical skill and common hand tools required; your machine's service manual for model-specific guidance.
• Disconnect power and water supply before beginning repairs to avoid shock or injury.
• Inspect related parts (agitator, dogs, bolt, and spline) and replace if worn to prevent repeat failure.

Includes suspension pads.