Kenmore Washer 110.21302010 (11021302010, 110 21302010) Parts

5 foot. Package of 2.

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

A replacement selector knob selection assembly that restores a secure, easy-to-turn control for cycle or setting selection. Replaces a cracked, loose, or missing knob so you can confidently select functions again. What it does:

• Replaces a worn, broken, or missing selector knob used to choose cycles or settings
• Provides a secure grip and positive engagement with the control shaft
• Helps stop slipping, wobbling, or a knob that won't turn properly
• Restores normal control operation when the original knob is damaged

• One selector knob selection assembly

• Disconnect power to the appliance before starting any repair
• Most knobs pull straight off the control shaft; align the splines and press on until fully seated
• If the knob resists, verify orientation—do not force to avoid shaft damage

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This siphon break kit prevents wastewater from siphoning back into the dishwasher, helping keep the tub and dishes clean and reducing drainback issues. Fits the dishwasher drain assembly to restore proper draining function. What it does:

• Stops backflow by breaking the siphon effect in the drain line
• Works with the dishwasher drain hose and pump to maintain one-way drainage
• Helps address symptoms like water remaining in the tub, partial drains, or water backing into the tub
• Supports proper drainage to reduce odors caused by standing water

• One siphon break kit

• Disconnect power to the appliance and turn off the water supply before starting
• Inspect the drain hose routing and secure the siphon break at the recommended height per the dishwasher's service instructions
• Use basic hand tools; hose clamps or fasteners may be required

This replacement brace reinforces appliance cabinet structure to restore proper alignment and reduce vibration. It helps maintain secure mounting of adjacent panels so doors and controls operate smoothly. What it does:

• Provides structural support for the appliance cabinet and connected panels
• Reduces rattling or vibration caused by loose or bent cabinet components
• Helps realign panels that are pulling away or not closing flush
• Useful when visible damage, bending, or missing support causes fitment issues

• Disconnect power and, if applicable, gas supply before starting any repair
• Remove outer cabinet panels or access panels to reach the brace mounting points
• Retain original fasteners when possible; replace damaged screws or clips as needed

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lower wire harness routes power and signals between the appliance's lower components, restoring electrical connections for reliable operation. It replaces a damaged or worn harness to help clear power interruptions and intermittent faults. What it does:

• Delivers power and signal connections to lower motors, switches, and sensors
• Re-establishes secure connector mating to prevent intermittent operation or loss of function
• Helps resolve symptoms such as no power to lower components, erratic operation, or related error codes
• Maintains correct wire routing and strain relief to reduce chafing or shorting

• Disconnect all power before starting — follow lockout/tagout where applicable
• Access may require removing panels or the lower access panel; keep track of fasteners
• Match connector shapes and routing to the original harness; do not force connectors
• Inspect surrounding wiring and terminals for heat damage or corrosion before reassembly

This absorber is the factory-design replacement part that restores the appliance's intended absorption function, helping maintain normal operation and reduce related performance issues. What it does:

• Absorbs and manages moisture/condensate or trapped vapors in the appliance's system to support normal function.
• Helps prevent symptoms commonly linked to a failed absorber, such as excess moisture, unusual odors, or intermittent system cycling.
• Restores the original fit and function when the installed absorber is cracked, broken, or heavily degraded.
• Matches OEM shape and connection points for a direct replacement.

• One absorber replacement as shown

• High-level replacement: access the absorber location; no specialized calibration typically required.
• Disconnect power (and water supply if applicable) before removing panels or replacing parts.
• Handle carefully to avoid damage to surrounding components and wiring; use manufacturer-recommended fasteners.

This tie wire secures wiring and small components to a tree-style mounting post, helping keep harnesses organized and preventing chafing or loose connections. Durable metal construction holds wiring in place for reliable operation. What it does:

• Secures wiring bundles and small components to a tree-style mount or post
• Helps prevent wires from rubbing against sharp edges or vibrating loose
• Reduces risk of intermittent electrical connections caused by loose harnesses
• Keeps internal wiring organized for safer, cleaner repairs

• Tie wire

• Disconnect power and unplug the appliance before servicing
• Position wires on the tree mount and wrap or fasten the tie wire
• Trim or bend any sharp ends to avoid contact with other parts or wiring
• Replace if damaged, corroded, or no longer holds wiring securely

This wire shield is a molded protective cover that helps keep wiring routed and protected from heat, abrasion and moving parts. It prevents chafing and reduces the risk of shorts for a safer appliance operation. What it does:

• Covers and routes wiring to protect insulation from heat and friction
• Prevents wires from contacting sharp edges or moving components
• Helps stop intermittent shorts, arcing, or wiring damage that can cause odor or failures
• Maintains proper wire position to support consistent electrical connections

• One wire shield

• Disconnect power to the appliance before beginning any work
• Secure with existing clips or fasteners; do not force or modify the part
• If wiring insulation is melted or damaged, replace wiring/harness before reassembly

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.