Kenmore Washer 110.42824200 (11042824200, 110 42824200) Parts

This replacement hose restores a secure, leak-free water path inside your appliance so it can move water where it's needed to fill, circulate, or drain correctly. Replacing a worn hose helps prevent leaks and related performance issues.

• Directs water between internal components as designed
• Maintains proper flow for filling, circulation, or draining
• Helps seal connections when correctly clamped and routed
• Common symptoms of a failed hose include leaks under the unit, slow or incomplete draining, erratic filling, or water-related error codes

• Disconnect power and shut off the water supply before servicing
• Note routing and orientation; replace one end at a time to match the original path
• Inspect and reuse OEM clamps if in good condition, or replace if corroded or weakened; fully seat all connections
• Run a brief test cycle and check all joints for leaks after installation

This front counterweight mounts to the washer's outer tub to help balance and stabilize the drum during spin. Replacing a damaged weight can reduce vibration and noise and help prevent the machine from walking. What it does:

• Adds mass at the front of the tub to counterbalance loads during spin
• Helps control vibration, shaking, and banging noises
• Can resolve out-of-balance interruptions or excessive movement
• Visible cracks or broken mounting ears indicate the weight needs replacement

• One front counterweight

• Disconnect power and water; use proper lifting techniques—this part is heavy
• Support the tub and remove front cabinet components/door boot as needed for access
• Remove and retain mounting bolts; tighten bolts evenly when reinstalling
• Inspect mounting points and suspension components while accessible; replace if worn

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This power cord is the replacement electrical lead that supplies mains power to the appliance, restoring safe, reliable operation when the original cord is damaged or worn. What it does

• Delivers AC power from the wall outlet to the appliance's internal wiring and controls.
• Replaces frayed, cut, melted, or otherwise damaged cords that can cause intermittent power or safety hazards.
• Helps eliminate issues like no power, intermittent power loss, or visible cord insulation damage.
• Restores a secure connection at the appliance strain-relief and terminal block when installed correctly.

• One replacement power cord.

• Always disconnect power at the circuit breaker or unplug the appliance before installing.
• Inspect terminal block and strain-relief; replace any damaged hardware and secure the cord per the appliance wiring diagram.
• Follow the appliance manufacturer's wiring diagram for correct conductor routing and grounding.

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This replacement screw is a direct-fit fastening part used to secure panels and small components on compatible Whirlpool appliances. It restores proper fit and helps stop loose or rattling parts for reliable appliance operation. What it does:

• Secures trim, panels, or brackets to keep parts aligned and stable
• Prevents vibration-related noise caused by loose hardware
• Replaces missing or damaged screws that allow components to shift
• Restores factory fit where stripped or worn fasteners fail

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use the proper screwdriver or driver bit to avoid stripping the head
• Install carefully and tighten until snug; do not overtighten
• Keep track of small parts and fasteners during disassembly

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This wire harness connects the appliance's control components so signals and power flow between modules for normal operation. It restores reliable electrical connections to help resolve control and power-related issues. What it does:

• Routes power and signal connections between control board components and sensors
• Replaces damaged or frayed wiring that can cause intermittent operation or loss of function
• Helps address symptoms such as unresponsive controls, no power to specific circuits, or intermittent operation
• Maintains secure connector fit to prevent arcing and improve reliability

• Disconnect power at the service panel before starting any work
• Match connector shapes and wire routing to the original harness before disconnecting; replace one-to-one
• Secure harness with existing clips/retainers and avoid pinching or sharp bends

This pushbutton is the simple replacement button that restores tactile control and appearance to your appliance's front panel. It snaps into the control panel and provides the same push action as the original part. What it does:

• Replaces a broken, cracked, or missing pushbutton so controls respond properly
• Restores a stuck or intermittently working button to a solid, reliable push action
• Prevents dirt and debris from entering the switch opening when installed
• Improves panel appearance when the original is worn or discolored

• One pushbutton replacement

• Disconnect power to the appliance before beginning any repair
• Usually a snap-in installation; gently press into the panel until it clicks
• May require removal of the control panel or trim for access—keep fasteners organized
• If the switch beneath is damaged, replace the switch assembly rather than just the button