Kenmore Washer 110.46747802 (11046747802, 110 46747802) Parts

This L-shaped flowmeter hose is part of the washer's water inlet circuit. It routes water through the flow sensor and maintains a tight, leak-free connection, helping the machine fill accurately and operate as designed.

• Channels incoming water through the flowmeter for correct fill measurement
• Maintains a secure, leak-resistant connection within the fill system
• Typical failure signs: water dripping during fill, visible cracking/hardening, loose fit, or kinks restricting flow
• A damaged or leaking hose can contribute to inaccurate fill sensing or fill-related errors

• Disconnect power and shut off both water supplies before servicing
• Note routing/orientation; transfer existing clamps or install new ones if needed
• Fully seat hose on each fitting and secure clamps without over-tightening
• Restore water and power, then run a fill to check all connections for leaks

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This O-ring is a direct replacement sealing ring that restores a watertight connection on the associated Whirlpool appliance assembly. Replacing a worn O-ring helps stop leaks and prevents water damage or drips at the joint. What it does:

• Provides a compressible seal between mating parts to prevent water leaks.
• Commonly used where hoses or fittings meet valves, dispensers or water lines.
• Fits into a groove to maintain pressure and stop slow drips or pooling.
• Replace when cracked, flattened, or pinched to restore proper sealing.

• Turn off water supply and unplug the appliance before replacing the seal.
• Remove the old O-ring, clean the mating surfaces, and inspect for nicks or debris.
• Lubricate the new O-ring if recommended by the manufacturer and seat it evenly in the groove.
• Test connections for leaks after restoring power and water.

This power cord is the replacement electrical lead that supplies mains power to the appliance, restoring safe, reliable operation when the original cord is damaged or worn. What it does

• Delivers AC power from the wall outlet to the appliance's internal wiring and controls.
• Replaces frayed, cut, melted, or otherwise damaged cords that can cause intermittent power or safety hazards.
• Helps eliminate issues like no power, intermittent power loss, or visible cord insulation damage.
• Restores a secure connection at the appliance strain-relief and terminal block when installed correctly.

• One replacement power cord.

• Always disconnect power at the circuit breaker or unplug the appliance before installing.
• Inspect terminal block and strain-relief; replace any damaged hardware and secure the cord per the appliance wiring diagram.
• Follow the appliance manufacturer's wiring diagram for correct conductor routing and grounding.

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This replacement screw is a direct-fit fastening part used to secure panels and small components on compatible Whirlpool appliances. It restores proper fit and helps stop loose or rattling parts for reliable appliance operation. What it does:

• Secures trim, panels, or brackets to keep parts aligned and stable
• Prevents vibration-related noise caused by loose hardware
• Replaces missing or damaged screws that allow components to shift
• Restores factory fit where stripped or worn fasteners fail

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use the proper screwdriver or driver bit to avoid stripping the head
• Install carefully and tighten until snug; do not overtighten
• Keep track of small parts and fasteners during disassembly

A small metal hose clamp that secures flexible hoses and tubing to fittings to help prevent leaks and keep connections tight. Simple, durable replacement for worn or loose clamps on appliance water and drain lines. What it does:

• Holds a hose or tube firmly on a barb or fitting to prevent leaks or disconnection
• Resists loosening from vibration and normal use
• Restores a secure connection when an old clamp is corroded, stretched, or broken
• Helps prevent water damage from loose plumbing connections

• One metal hose clamp

• Disconnect power and shut off water supply before servicing
• Slide clamp over hose, position over fitting barb, then compress or tighten as required
• Replace any damaged hoses or fittings when installing a new clamp
• Verify a leak-free connection before returning appliance to service

This steamer heater assembly produces the heat needed for a dryer's steam/refresh cycles so clothes receive steam for wrinkle reduction and odor release. Replaces a failed or weak steam heater to restore steam functionality. What it does

• Heats water into steam for the dryer's steam/refresh feature.
• Helps restore steam output when the steam option produces little or no steam.
• Can resolve issues where steam cycles do not start or clothing remains unrefreshed after a steam cycle.
• Works as the thermal element portion of the dryer's steamer system.

• One steamer heater assembly

• Disconnect power to the appliance before beginning any service.
• Handle the heater assembly carefully; avoid bending terminals or stressing mounts.
• Basic mechanical skill and common tools are typically required; for panel removal and wiring diagrams.

This dispenser assembly mounts in the refrigerator door to provide a stable dispensing point for ice and water and restore normal use of the door dispenser. It replaces damaged or worn dispenser components to stop leaks and restore proper operation. What it does:

• Provides the exterior opening and actuator area for dispensing ice and/or water
• Guides and supports the dispense lever or actuator and related components
• Helps prevent leaks and dripping from the door dispense area
• Commonly replaced when the dispenser won't actuate, leaks, or has broken trim or lever

• Disconnect power and shut off the water supply before starting
• Door panel or inner liner removal may be required for access
• Handle trim and plastic parts carefully to avoid cracking during removal/installation
• Follow the refrigerator's service manual or tech sheet for torque and routing details