Kenmore Washer 110.47542602 (11047542602, 110 47542602) Parts

The Vent Hose is an OEM part for Whirlpool washing machines. This vent hose allows air to circulate in and out of the washer, preventing pressure build-up and ensuring proper water drainage. It helps maintain the efficiency and effectiveness of the washing machine by facilitating the necessary airflow during the wash and spin cycles.

Common causes of a bad vent hose include wear and tear from regular use, blockages from lint or debris, and damage from mishandling or improper installation.

Symptoms of a bad vent hose include:

• Water not draining properly from the washer
• Unusual noises during the wash or spin cycles
• Leaks or water pooling around the washer
• Visible cracks, splits, or blockages in the hose

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Connector lever

This is a washing machine control board. It is also known as the mainboard or motherboard and manages the timing of the washing machine. This part also makes sure all proper washer functions are carried out when appropriate. The control board controls the drive motor, fill valves, and drain pump. If this part is damaged, button presses may not work. The washing machine may not start or complete certain cycles.If the control board is damaged or non-functioning, it will need to be replaced. However, before starting, make sure the washing machine is disconnected from power. The water supply should also be shut off. Pull the washing machine away from the wall and take off the control knob before removing the back panel. Take out the control board and reconnect the wires to the new component before reassembly.The control board has been created to be compatible with Kenmore washing machines. It's directly sourced from the manufacturer as a genuine OEM replacement part. This component is sold individually.

This rubber seal fits around the water temperature sensor where it passes through the tub or housing. It restores a watertight barrier at the sensor port to help prevent leaks and ensure reliable temperature feedback.

• Creates a watertight seal around the temperature sensor
• Helps prevent drips or leaks from the sensor opening
• Supports stable, accurate temperature readings during cycles
• Typical failure signs: cracked, flattened, or brittle seal; moisture at the sensor area; pooling water beneath the unit; temperature-related faults

• Disconnect power and turn off water supply before servicing
• Access the sensor location and drain any remaining water
• Withdraw the sensor, remove the old seal, and clean the seating surface
• Lightly moisten the new seal with water, seat it fully, reinstall the sensor, and check for leaks during a test cycle

This siphon routes liquid bleach and fabric softener from the dispenser into the washer tub so additives are delivered at the correct time in the cycle. Replacing a faulty siphon restores proper dispensing and helps prevent leaks or staining. What it does:

• Directs bleach and fabric softener from the dispenser to the wash drum during the appropriate cycle.
• Ensures additives are introduced at the correct time for consistent wash results.
• A cracked, clogged, or broken siphon can cause poor dispensing, leaks, or product staining.
• Designed to fit into the dispenser assembly and work with the washer's existing dispenser plumbing.

• Disconnect power (and water if recommended) before servicing the appliance.
• Basic hand tools may be required; refer to the washer's service manual for disassembly steps.
• Handle plastic components gently to avoid cracking or misalignment of sealing surfaces.

This distribution nozzle directs water flow inside the dishwasher to help ensure proper spray coverage and detergent/rinse aid distribution. Replacing a damaged nozzle restores targeted water delivery for better cleaning and drying performance. What it does:

• Directs and shapes spray from the wash assembly for targeted cleaning
• Helps distribute rinse aid/detergent where designed for optimal results
• Prevents leaks or misdirected spray caused by cracks or clogs
• Faulty nozzles can cause poor cleaning, spotting, or uneven wash performance

• Disconnect power and water supply before beginning any repair.
• Inspect surrounding spray arm/assembly for damage or debris before installation.
• Most installs are a snap-fit or secured with simple fasteners; avoid over-tightening.

This counterweight helps balance and stabilize a refrigerator door so it opens and closes smoothly and stays in the desired position. It replaces a worn or damaged weight to restore proper door operation. What it does:

• Adds counterbalance to a fridge door so it doesn't slam shut or drift open
• Restores even, controlled door movement and alignment
• Helps reduce stress on door hinges and seals
• Commonly replaced when the door feels heavy on one side or won't stay open

• One counterweight

• Disconnect power to the appliance before beginning any repair
• Support the door while removing/installing the counterweight to avoid injury or damage
• Basic hand tools may be required; refer to your service manual for exact steps

This oven door glass replaces a cracked or broken glass panel so the door seals and you can safely see inside while cooking. It restores the oven door's protective barrier and appearance. What it does:

• Replaces damaged or cracked oven door glass to prevent heat loss and sharp edges
• Restores visibility into the oven cavity for safe monitoring of food
• Helps the door maintain proper sealing when paired with intact gaskets and hardware
• Reduces risk of glass shards or injury from a compromised panel

• Handle with care; glass is fragile—use gloves and eye protection during removal and installation
• Disconnect power and allow the oven to cool before working on the door
• Follow the oven manufacturer's instructions for removing the door and fastening the glass
• If door hardware or seals are damaged, inspect and replace them separately

This outer tub is the dishwasher's main outer wash tub shell that helps contain water and support internal components. Replacing a damaged outer tub restores the cabinet seal and helps stop leaks and moisture damage. What it does

• Houses and supports the inner tub, pump, and other internal components.
• Contains wash water to prevent leaks from reaching the cabinet or flooring.
• Helps maintain proper alignment for spray arms and seals to function.
• Commonly replaced when the tub is cracked, warped, or allowing water to escape.

• One outer tub.

• Disconnect power and water before starting; follow OEM disassembly steps for your model.
• Replacement typically requires removing the dishwasher door, control console, and interior components; keep fasteners organized.
• Inspect and replace gaskets, seals, and mounting hardware as needed for a watertight repair.

Color: White. Size: 1 qt. can. Acrylic appliance paint.