Kenmore Washer 110.47788800 (11047788800, 110 47788800) Parts

This electrical connector links wiring within the appliance's harness, restoring a secure, reliable connection for proper operation. Use it to replace a damaged or corroded connector that's causing intermittent power or component failures.

• Creates a solid electrical connection between harness leads
• Helps resolve issues like intermittent operation, no power to a component, or visible heat damage at a connection point
• Maintains correct current flow and reduces risk of arcing at loose terminals
• Designed to fit the specified harness location per model

• Disconnect power and shut off utilities before servicing
• Match wire colors/positions and transfer one lead at a time to avoid miswiring
• Ensure terminals are fully seated and the connection is snug
• Inspect surrounding wiring for heat damage or corrosion and address as needed

This clamp secures a flexible appliance hose to a fitting to help prevent leaks and keep connections tight. It's a small but essential part that restores a proper seal on water or drain lines. What it does:

• Holds a hose firmly to a tailpiece, barb or connector to reduce leaks and hose slippage
• Helps stop intermittent dripping or pooling caused by loose hose connections
• Restores a proper seal after hose replacement or maintenance
• Works on common appliance water/drain lines where this clamp style is used

• One hose clamp

• Disconnect power and shut off water to the appliance before starting any work
• Allow the appliance and hoses to cool if recently used; use gloves and eye protection
• Use appropriate pliers or a screwdriver (depending on clamp style) to remove and install the clamp; avoid over-tightening
• Inspect the hose and fitting for damage; replace the hose if cracked or worn

This is a single replacement screw used to secure appliance panels and components. It restores proper fastening to help eliminate looseness and rattling and keep parts aligned for safe operation. What it does:

• Secures trim, panels or internal components to maintain proper alignment
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or stripped screws for safe, reliable fit
• Works wherever the OEM screw specification and fit match the original

• One screw as shown

• Disconnect power and/or gas before accessing internal components
• Use the proper driver size and avoid over-tightening to prevent thread damage
• Verify correct screw placement against the appliance's service diagram

This replacement screw secures appliance panels and trim so components stay properly aligned and vibration is reduced. Use it to replace missing or damaged fasteners and restore a secure fit for safe operation. What it does:

• Fastens control panels, trim pieces, or access panels to the appliance frame
• Prevents panel movement, rattling, or gaps that can form from loose or missing screws
• Restores proper alignment after service or part replacement
• Helps maintain safe, stable operation by keeping panels secured

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct driver bit and thread engagement; hand-start threads to avoid cross-threading
• Do not overtighten — snug until secure to avoid stripping or damaging panel threads
• Keep removed hardware organized to ensure correct locations during reassembly

This exhaust hose carries drain water from the pump to the external drain connection on your washer. Replacing a worn or damaged hose restores proper draining and helps prevent leaks and musty odors.

• Directs discharge water from the drain pump toward the outlet
• Maintains a sealed flow path to help prevent leaks
• Age, vibration, or debris can cause cracks, splits, or clogs
• Common symptoms: water leaking under the unit, slow or no drain, visible cracks/kinks on the hose

• Disconnect power and turn off water supply before servicing
• Place towels or a pan to catch residual water; remove access panels as needed
• Compress/release spring clamps, transfer them to the new hose, and fully seat hose ends
• Run a short drain cycle to check for leaks

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This power cord is the replacement electrical lead that supplies mains power to the appliance, restoring safe, reliable operation when the original cord is damaged or worn. What it does

• Delivers AC power from the wall outlet to the appliance's internal wiring and controls.
• Replaces frayed, cut, melted, or otherwise damaged cords that can cause intermittent power or safety hazards.
• Helps eliminate issues like no power, intermittent power loss, or visible cord insulation damage.
• Restores a secure connection at the appliance strain-relief and terminal block when installed correctly.

• One replacement power cord.

• Always disconnect power at the circuit breaker or unplug the appliance before installing.
• Inspect terminal block and strain-relief; replace any damaged hardware and secure the cord per the appliance wiring diagram.
• Follow the appliance manufacturer's wiring diagram for correct conductor routing and grounding.

This drum baffle (drum lifter) helps lift and separate laundry as the drum turns to promote even tumbling and improved air circulation for better drying. Designed to replace a worn or damaged lifter and restore normal drum action. What it does:

• Lifts and moves clothes during a drying cycle to prevent clumping and improve airflow
• Helps maintain even tumbling to reduce drying times and uneven drying
• Replaces broken, cracked or missing lifters that can cause noise or fabric snags
• Contributes to quieter operation by restoring proper load balance

• One drum baffle (drum lifter)

• Disconnect power (and gas supply if applicable) before starting any repair
• Replacement typically requires access to the dryer cabinet and drum — keep fasteners and clips in a safe place
• Inspect mounting points and surrounding drum for wear; replace any damaged hardware
• Test run the dryer after installation to ensure secure fit and normal operation

A small metal hose clamp that secures flexible hoses and tubing to fittings to help prevent leaks and keep connections tight. Simple, durable replacement for worn or loose clamps on appliance water and drain lines. What it does:

• Holds a hose or tube firmly on a barb or fitting to prevent leaks or disconnection
• Resists loosening from vibration and normal use
• Restores a secure connection when an old clamp is corroded, stretched, or broken
• Helps prevent water damage from loose plumbing connections

• One metal hose clamp

• Disconnect power and shut off water supply before servicing
• Slide clamp over hose, position over fitting barb, then compress or tighten as required
• Replace any damaged hoses or fittings when installing a new clamp
• Verify a leak-free connection before returning appliance to service