Kenmore Dryer 110.62512101 (11062512101, 110 62512101) Parts

This is a drum assembly intended for use with dryers. This part can be found inside the dryer and is responsible for holding clothing while a cycle is running. It holds wet laundry while loading the appliance. Over time and with use, the drum assembly can start to wear out. This can cause the dryer to squeal, start and stop during a cycle, make buzzing noises, or seize up.If the drum assembly is damaged, it will need to be replaced. Make sure to have basic tools and a pair of work gloves ready. The dryer should be turned off and unplugged from the wall. Raise the top panel, remove the front panel, and then remove the drum. The drum support roller should be taken out and installed on the new drum. Reinstall with the new component and reassemble all parts before use.The drum assembly is made to be used with dryers and washer/dryer combos from Inglis, Estate, Admiral, Crosley, Roper, Magic Chef, Amana, KitchenAid, Maytag, Kenmore, and Whirlpool. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold on an individual basis.

Color: White.

This wire harness assembly routes power and control signals between components so the appliance operates reliably. It replaces a damaged or worn harness to restore proper electrical connections and reduce intermittent faults. What it does:

• Provides the main connector wiring between electrical components and the control board.
• Restores lost power or control signals caused by broken, frayed, or burnt wires.
• Helps stop intermittent operation, control errors, or components that won't power on.
• Maintains secure connector fit and correct wire routing to prevent shorting.

• Always disconnect power (unplug or switch off breaker) before starting any repair.
• Handle connectors carefully; release locking tabs to avoid damage.
• Route and secure the harness following original wire paths and clips to prevent chafing.

This is a replacement 8-18 x 7/32 machine screw used to secure panels and small components in compatible Whirlpool appliances. It restores proper fastening where a screw is missing, stripped, or damaged. What it does:

• Secures panels, trim pieces, brackets or small components to prevent movement
• Helps stop rattling, vibration noise, or loose-fitting parts
• Replaces missing or damaged screws to restore proper alignment of panels or controls
• Used wherever an 8-18 x 7/32 machine screw is specified by the manufacturer

• Unplug the appliance or turn off power before servicing.
• Use the correct screwdriver or bit to avoid stripping the head; tighten snugly but do not over-torque.
• Replace any stripped inserts or mating hardware if threads are damaged.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This control knob replaces a worn or broken appliance control interface so you can set temperatures and cycle settings easily. It restores a secure grip and clear position indication for smooth operation of the appliance control shaft. What it does:

• Fits onto a control shaft to select heat level, timer, or function settings
• Provides a clear indicator for accurate knob position and user control
• Restores a stable, slip-free grip when turning the control
• Helps eliminate loose, cracked, or missing knob symptoms that prevent proper control input

• One replacement control knob

• Slide the knob straight onto the control shaft until fully seated; no tools usually required
• The shaft and knob splines must match before pressing on to avoid damage
• If the original mounting or shaft is damaged, replacement of the underlying control may be required
• Disconnect power to the appliance before attempting any repair for safety

This blower-housing pad is a replacement foam/rubber seal that cushions the blower assembly and helps maintain proper airflow and fit. It restores the original fit between the blower housing and cabinet to reduce vibration and air gaps. What it does:

• Cushions and supports the blower housing to reduce noise and vibration during operation
• Helps seal the blower housing to prevent air leaks that can reduce performance
• Maintains proper alignment and spacing of the blower assembly inside the cabinet
• Common symptom: excessive vibration, rattling, or airflow leakage near the blower area

• Designed for direct replacement; part number matches your unit before ordering
• Turn off power to the appliance at the breaker before beginning repair
• Handle foam/rubber parts gently to avoid tearing; ensure pad seats fully around the housing
• If other blower components are worn or damaged, inspect and replace as needed