Kenmore Dryer 110.68002010 (11068002010, 110 68002010) Parts

This electronic control board (CCU Sahara2 VMD) replaces the oven's main control module to restore front-panel controls and manage bake/broil cycles. It helps the range respond correctly to button presses and control oven functions. What it does:

• Receives input from the touchpad/knobs and runs the oven control logic
• Sends commands to heating elements, relays and sensors for bake/broil cycles
• Updates and displays status on the control/clock interface
• Common symptom fixes: blank or unresponsive display, unresponsive front-panel controls, or erratic oven behavior

• Disconnect power at the breaker before starting any work
• Handle the board carefully to avoid ESD damage and avoid touching circuit traces
• Reconnect all wiring connectors to their original locations; confirm secure seating
• After installation, restore power and verify oven functions

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This door seal is a flexible refrigerator gasket that helps keep the cabinet airtight to maintain proper cooling and efficiency. Replaces a worn, torn, or misshapen seal to reduce cold air loss and improve temperature stability. What it does:

• Forms an airtight seal between the refrigerator door and cabinet to help keep cold air in
• Helps prevent frost build-up and reduces the workload on the compressor
• Commonly replaced when the gasket is cracked, torn, flattened, or allowing cold air to leak
• Compatible with models that use PN W10325058

• One door seal / refrigerator door gasket

• Basic push-in or screw-in installation; follow your appliance's service manual for the correct procedure
• Inspect the door frame and fastening channel for debris before installing the new seal
• Warm the gasket with a hair dryer (low heat) or allow time for it to relax to improve fit, as needed
• Disconnect power to the appliance before any service that requires removing panels or working near electrical components

This exhaust pipe routes exhaust air from the appliance to the home vent, restoring proper airflow for safe, efficient operation. Use when the original pipe is cracked, bent, or leaking. What it does:

• Channels exhaust gases and lint from the appliance to the external vent
• Prevents exhaust leaks that can cause poor drying or cooking performance
• Helps maintain correct airflow to reduce overheating and moisture buildup
• Fits where a damaged or corroded exhaust connection needs replacement

• One exhaust pipe

• Disconnect power (and gas if applicable) before servicing; follow appliance safety procedures
• Inspect surrounding seals and clamps; replace clamps or ducting if damaged
• Secure pipe with OEM-recommended fasteners and ensure vent path is clear

This exhaust pipe vents hot, moist air from the dryer to the home venting system, helping the appliance dry clothes efficiently and reduce indoor humidity. Replace a damaged or restricted pipe to restore proper airflow. What it does:

• Channels dryer exhaust air safely from the appliance to the exterior vent
• Helps prevent overheating and long dry times caused by restricted airflow
• Reduces lint buildup in the appliance by providing a clear vent path
• Commonly replaced when cracked, crushed, kinked, or badly corroded

• Disconnect power to electric dryers; shut off gas supply and disconnect for gas dryers before servicing
• Inspect existing vent path for additional damage or lint buildup and clean before installing
• Position pipe without sharp bends or kinks and secure with appropriate clamps or fasteners

This mounting bracket provides a secure support point inside the appliance to hold panels or components in place, restoring proper fit and reducing movement. It's a simple replacement when a worn or broken bracket causes loose parts. What it does:

• Supports and anchors interior panels or components to the appliance frame
• Restores proper alignment and eliminates rattling or shifting parts
• Replaces cracked, bent or missing brackets that prevent secure mounting
• Helps maintain normal operation by keeping parts positioned correctly

• One mounting bracket

• Always disconnect power and water before starting repairs
• Verify bracket orientation against the original part; keep hardware or replace with matching screws
• Use common hand tools; avoid over-tightening fasteners to prevent cracking

This exhaust pipe directs heated air from the dryer drum to the household vent, restoring proper airflow for efficient drying and reduced lint buildup. It's a direct-fit replacement designed to match the OEM airflow path. What it does:

• Channels dryer exhaust from the appliance to the external vent to maintain proper airflow.
• Helps prevent lint accumulation in the cabinet by providing a sealed exhaust path.
• Can reduce long dry times and overheating caused by restricted or damaged venting.
• Addresses symptoms such as poor drying performance, hot dryer cabinet, or noticeable burning/overheating smells near the dryer vent area.

• One exhaust pipe.

• Disconnect power (and gas, if applicable) before starting work; the appliance is fully de-energized.
• Wear gloves to avoid sharp edges; remove old pipe and clean vent connections before installing the replacement.
• Secure with appropriate clamps or fasteners and ensure a continuous, unobstructed path to the exterior vent.
• After installation, run a short cycle to check for leaks.