Kenmore Washer 110.6914751 (1106914751, 110 6914751) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP96160
This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.
- Connects water tubing between components within the appliance's water system
- Helps maintain a tight, leak-resistant seal at the joint
- Restores proper water flow when a tube or connector is damaged
- Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit
What's included: One adapter tube assembly. Install notes:
- Disconnect power and shut off the water supply before servicing
- Relieve line pressure and place a towel or pan to catch any residual water
- Note routing and orientation before removal to ensure correct reassembly
- After installation, restore water and check all connections for leaks
Do-It-Yourself Stories from Customers like You
Washing machine was having trouble delivering enough water on rinse cycle Cynthia S. • Libertyville , IL • August 15, 2014
Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you!
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.
- Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
- Replaces a lost, worn, or damaged anti-rattle fastener
- Helps maintain proper alignment and prevents vibration-related wear
- Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet
What's included: One anti-rattle screw Installation notes:
- Disconnect power before servicing; for gas appliances, shut off the gas supply
- Access the mounting point and remove the loose or damaged screw
- Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
- Repair or replace the bracket/clip before reassembly
Do-It-Yourself Stories from Customers like You
No spin on spin cycle Richard S. • Beaumont , CA • August 28, 2015
Replaced clutch assembly which was a little tricky, but very doable. Just make sure to take your time. I do have to say that I am very impressed with AppliancePartsPro customer service when the replacement part also failed. A new clutch assembly was at my door step a few days later. I now has a working washer again. Thanks Again Appliance Parts Pro.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.95
- Compare At:
-
$11.59
- You Save:
-
$1.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.
- Provides a protective wear surface between the hinge and cabinet/lid
- Reduces squeaks, creaks, and rattling when opening or closing the lid
- Helps maintain proper lid alignment and smooth movement
- Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid
What's included: 1 hinge pad Installation notes:
- Disconnect power to the washer before servicing
- Support the lid to relieve hinge tension and access the hinge area per your model
- Remove the worn pad and press the new pad fully into the hinge location
- Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$19.79
- Compare At:
-
$21.36
- You Save:
-
$1.57
Genuine Whirlpool part
By: Whirlpool
Part Number: 350365
2 Port. Whirlpool and Kenmore washers.
Do-It-Yourself Stories from Customers like You
Water drain pump would not turn any more Robert T. • Belleville , IL • January 20, 2016
Ordered a replacement. Had to tip washer toward the back to provide access underneath to the
pump. Had some difficulty removing the two hose clamps. Pliers were not the best tool. Had to ensure the drive belt was properly engaged with the pulley of the pump.
Read more
More
$92.56
- Compare At:
-
$110.15
- You Save:
-
$17.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62837
Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:
- Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
- Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
- Common service symptom: knob spins freely or fails to engage controls.
- Used where a small metal pin is required to lock a component onto a splined or smooth shaft.
What's included: One straight knurled pin. Install notes:
- Disconnect power and unplug the appliance before servicing.
- Remove the knob or access panel to reach the shaft; pin is typically press-fit.
- Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
- Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.
Do-It-Yourself Stories from Customers like You
Whirlpool shaking Willy P. • Victorville , CA • May 19, 2019
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good.
Read more
More
$7.47
- Compare At:
-
$8.89
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596797
Genuine Whirlpool part
By: Whirlpool
Part Number: WP94614
For mating terminal use [AP31136300].
More
$4.95
- Compare At:
-
$5.89
- You Save:
-
$0.94
Genuine Whirlpool part
By: Whirlpool
Part Number: 358277
Made by Whirlpool. Fits most Whirlpool, Kenmore, Estate and Roper belt driven washing machines.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine would not stop dripping into basket when finished washing Howard S. • Minneapolis , MN • April 25, 2021
Replaced washer water inlet valve.
Read more
More
$93.72
- Compare At:
-
$111.53
- You Save:
-
$17.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21365
This small hardware washer is used as a spacer and load distributor within the specified assembly. It helps maintain alignment and smooth operation by reducing friction and restoring a secure fit when the original washer is worn or missing. What it does:
- Distributes load under a screw or bolt to keep joints secure
- Maintains proper spacing and alignment between mating parts
- Reduces friction and wear at the contact surface
- Replace if missing, bent, cracked, or excessively worn; clues include wobbly parts or scraping/squeaking noises
What's included:
Install notes:
- Disconnect power and shut off water supply before servicing
- Refer to your model's parts diagram for exact location and stack order
- Clean mating surfaces; replace any damaged fasteners or bushings
- Tighten hardware evenly and do not overtighten
Do-It-Yourself Stories from Customers like You
Washing machine would not agitate or spin. Laurie W. • Webster , NH • March 25, 2017
We were a bit doubtful that we could find parts for this Whirlpool washing machine as it is 22 years old. We were SO pleased that not only could we find them ( with excellent customer service) but they were shipped in an appropriate time. My handy husband was then able to repair it himself :)
Read more
More
$7.40
- Compare At:
-
$8.88
- You Save:
-
$1.48
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3351614
Size: 10-24 x 3/8 inch.
Do-It-Yourself Stories from Customers like You
Timer/control failed Gilbert G. • Lansing , IL • July 09, 2018
Replaced timer control unit, first time doing this.
Read more
More