Kenmore Dryer 110.69622800 (11069622800, 110 69622800) Parts

This blower housing assembly directs airflow from the dryer's drum to the exhaust, helping the appliance vent properly for efficient drying. It replaces a damaged or cracked housing to restore correct air path and reduce airflow loss. What it does:

• Guides air from the drum to the blower wheel and exhaust vent for proper drying performance
• Supports and locates the blower wheel and related seals to maintain airflow integrity
• Can reduce or stop airflow issues like poor drying or extended cycle times when cracked or broken
• May resolve abnormal noise caused by a loose or damaged housing contacting the blower wheel

• One blower housing assembly

• Disconnect electrical power (and gas supply for gas dryers) before servicing
• Access typically requires removing the dryer cabinet or back panel; follow the OEM service manual
• Inspect the blower wheel and motor while replacing the housing; replace any worn components
• After installation, check for proper wheel clearance and exhaust airflow and quiet operation

A replacement selector knob selection assembly that restores a secure, easy-to-turn control for cycle or setting selection. Replaces a cracked, loose, or missing knob so you can confidently select functions again. What it does:

• Replaces a worn, broken, or missing selector knob used to choose cycles or settings
• Provides a secure grip and positive engagement with the control shaft
• Helps stop slipping, wobbling, or a knob that won't turn properly
• Restores normal control operation when the original knob is damaged

• One selector knob selection assembly

• Disconnect power to the appliance before starting any repair
• Most knobs pull straight off the control shaft; align the splines and press on until fully seated
• If the knob resists, verify orientation—do not force to avoid shaft damage

This 5/16-18 x 3/4 machine bolt replaces a missing or damaged fastener used to secure panels, brackets and components in many home appliances. It restores proper fit and helps stop rattling or loose parts. What it does:

• Secures panels, brackets or assemblies to maintain proper alignment and safe operation
• Restores clamping force where a stripped or missing bolt lets parts shift or vibrate
• Helps eliminate rattling, scraping or movement caused by loose fasteners
• Matches standard 5/16-18 coarse threads for direct replacement of the OEM bolt

• Disconnect power to the appliance before servicing to reduce shock and injury risk
• Start threads by hand to avoid cross-threading; tighten using the correct socket or wrench
• Do not overtighten; snug to manufacturer torque or until secure to avoid stripping threads
• If the original mating threads are damaged, inspect the receiving part and repair or replace as needed

This retaining clip secures plastic and metal panels and small assemblies to keep parts aligned and reduce movement. It replaces a worn or broken clip to restore proper fit and stop loose panels or rattling. What it does:

• Holds trim, panels or housings in place to maintain proper alignment
• Prevents parts from shifting or vibrating during operation
• Helps stop rattling or intermittent contact caused by a missing clip
• Serves as a simple mechanical fastener — no tools beyond basic hand tools may be needed for access

• Disconnect power to the appliance before beginning any repair.
• Access may require removing panels or trim; keep fasteners organized.
• Inspect mating surfaces and adjacent clips; replace additional clips if brittle or damaged.

This harness clip secures appliance wiring to the cabinet or components to prevent rubbing, pinching, and interference with moving parts. It keeps wiring routed neatly for reliable operation and reduced risk of abrasion-related failures. What it does:

• Holds wire harnesses in place to prevent chafing against sharp edges or moving parts
• Reduces vibration-related noise and intermittent connections caused by loose wiring
• Helps maintain proper wire routing around panels, motors, and heaters
• Supports safe operation by keeping wires away from heat sources and pinch points

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove panels or access covers as needed to reach the original clip location
• Install by snapping or seating the clip into the original mounting point and securing the harness in the retainer; replace any broken mounts
• Inspect surrounding wiring and replace damaged wires or insulation before completing repair

This endcap assembly replaces a worn or damaged endcap to restore proper fit and protect the appliance's exposed end components. It helps keep parts aligned and prevents rubbing, vibration, and debris entry for smoother operation. What it does:

• Secures and protects the exposed end of the related component or housing
• Maintains proper alignment to reduce vibration, noise, and premature wear
• Replaces cracked, broken, or missing endcaps that allow movement or debris intrusion
• Restores finished appearance where the original endcap is damaged

• Disconnect power (and water if applicable) before starting any repair.
• Installation usually involves aligning the endcap and fastening or snapping it into place; confirm orientation before securing.
• Keep track of any screws or clips removed and reuse original fasteners unless replacements are specified.

This rear panel replaces the cabinet back on compatible Whirlpool appliances to protect internal components and close the cabinet for proper airflow and safety. It restores the appliance's enclosure and keeps wiring and controls covered. What it does:

• Covers and protects internal parts at the back of the appliance from dust and physical damage
• Helps maintain proper airflow paths for cooling and ventilation
• Restores the appliance cabinet for a finished appearance
• Can reduce vibration-related noise by securing rear components

• One rear panel as described

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove access panels and mounting screws to replace the rear panel; retain hardware
• Handle sharp edges carefully and wear gloves to avoid cuts
• Note wiring or components are tucked to the panel, their routing before removal and restore exactly

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This drum is the rotating tub that holds clothes and provides the tumbling action needed for cleaning or drying. It restores the drum surface and rotation area to help the appliance tumble items properly. What it does:

• Replaces a damaged, dented, or cracked drum to restore a smooth tumbling surface
• Supports normal rotation so clothes move through the wash or dry cycle evenly
• Helps reduce rubbing, scraping, or loud metal-on-metal noises from the cabinet
• Addresses symptoms like visible drum damage, fabric catching, or items not tumbling

• One replacement drum

• Disconnect power and water before starting any repair
• Installation typically requires disassembling the front or top panel and removing the old drum, belt, and related fasteners
• Inspect and replace worn belts, rollers, seals, or bearings while servicing the drum

This light socket holds the appliance bulb and provides a reliable electrical connection, restoring clear visibility inside your unit. Replace a cracked, heat-damaged, or loose socket to fix lights that flicker, go out, or won't stay seated.

• Secures the bulb and makes proper electrical contact with the wiring
• Powers the bulb when the control or door switch commands illumination
• Helps maintain consistent lighting during normal operation
• Typical symptoms: light won't turn on with a good bulb, flickers, intermittent lighting, burnt or brittle socket, bulb won't stay seated

• Disconnect power to the appliance before servicing; allow hot areas to cool
• Note wire locations and socket orientation; take a photo before removal
• Transfer any mounting screws/bracket from the old socket as needed
• Install the correct bulb type and wattage per your appliance manual; do not overtighten

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued