Kenmore Washer 110.71423200 (11071423200, 110 71423200) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP367594
This front foot assembly is the adjustable leveling leg located at the front of the appliance. It supports and stabilizes the cabinet so it sits square and level, helping prevent rocking, vibration, and poor door alignment.
- Provides front support and height adjustment to level the unit
- Helps reduce rocking, vibration, and rattling during operation
- Replaces a worn, broken, missing, or stripped front foot
- Helps ensure doors or drawers align and close properly when leveled
What's included: 1 front foot assembly Install notes:
- Disconnect power and, if applicable, shut off water/gas before servicing
- Protect flooring; carefully tip or brace the appliance to access the front foot
- Unthread the old foot; thread in the new foot and adjust until level side-to-side and front-to-back
- Verify stability, then restore utilities and recheck for level
Do-It-Yourself Stories from Customers like You
Front foot was damaged Deborah L. • Mount Pleasant , WI • June 08, 2015
Replaced, it was a cinch!!!
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$19.79
- Compare At:
-
$21.36
- You Save:
-
$1.57
Genuine Whirlpool part
By: Whirlpool
Part Number: WP354255
A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:
- Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
- Reduces vibration and rattling during operation
- Helps doors and panels sit properly when closed
- Simple, non-electrical part — no wiring or adjustment required
What's included:
Install notes:
- Inspect the mounting hole or surface; clean debris before installing
- Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
- Disconnect power to the appliance first and follow OEM instructions
- Remove old adhesive before installing the new bumper
Do-It-Yourself Stories from Customers like You
Broken fill valve John N. • Tumwater , WA • July 14, 2015
The video associated with the part was easy to understand. The actual repair was easy - maybe 10 minutes. But getting the top casing of the washer fitted back over the base was a huge pain. That took 8 tries to finally get it locked in just right. The washer is 20+ years old though.
The parts were all exactly correct and fit perfectly. Shipping time was excellent. Parts arrived in about 2 days with "standard" shipping.
The washer works great now. This is the second major repair I've done...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21365
This small hardware washer is used as a spacer and load distributor within the specified assembly. It helps maintain alignment and smooth operation by reducing friction and restoring a secure fit when the original washer is worn or missing. What it does:
- Distributes load under a screw or bolt to keep joints secure
- Maintains proper spacing and alignment between mating parts
- Reduces friction and wear at the contact surface
- Replace if missing, bent, cracked, or excessively worn; clues include wobbly parts or scraping/squeaking noises
What's included:
Install notes:
- Disconnect power and shut off water supply before servicing
- Refer to your model's parts diagram for exact location and stack order
- Clean mating surfaces; replace any damaged fasteners or bushings
- Tighten hardware evenly and do not overtighten
Do-It-Yourself Stories from Customers like You
Washing machine would not agitate or spin. Laurie W. • Webster , NH • March 25, 2017
We were a bit doubtful that we could find parts for this Whirlpool washing machine as it is 22 years old. We were SO pleased that not only could we find them ( with excellent customer service) but they were shipped in an appropriate time. My handy husband was then able to repair it himself :)
Read more
More
$7.40
- Compare At:
-
$8.88
- You Save:
-
$1.48
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596797
Genuine Whirlpool part
By: Whirlpool
Part Number: 358277
Made by Whirlpool. Fits most Whirlpool, Kenmore, Estate and Roper belt driven washing machines.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine took 30 minutes to fill because the inlet valve was failing Chris G. • Dunedin , FL • June 13, 2016
I ordered the replacement inlet valve from your site, installed it in 20 minutes. the washing machine now fills to extra large capacity in 3 minutes. The machine is an old Kenmore bought new in 1985, this inlet valve is the only component to fail in the over 30 years we have had it.
Read more
More
$93.72
- Compare At:
-
$111.53
- You Save:
-
$17.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP94614
For mating terminal use [AP31136300].
More
$4.95
- Compare At:
-
$5.89
- You Save:
-
$0.94
Genuine Whirlpool part
By: Whirlpool
Part Number: 350938
Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Dryer drum completely wore off all coating Larry W. • Ubly , MI • July 01, 2016
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do
Read more
More
$46.95
- Compare At:
-
$55.87
- You Save:
-
$8.92
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3351614
Size: 10-24 x 3/8 inch.
Do-It-Yourself Stories from Customers like You
Timer/control failed Gilbert G. • Lansing , IL • July 09, 2018
Replaced timer control unit, first time doing this.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP358160
This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.
- Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
- Helps prevent fasteners from loosening due to vibration and thermal cycling
- Common fix for rattling/vibration noises and components that work loose over time
- Replaces damaged, rounded, or missing original nut to restore proper fit
What's included: 1 lock nut Install notes:
- Disconnect power and shut off gas/water supplies before servicing
- Remove the worn nut with the appropriate wrench or socket
- Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
- Inspect the mating bolt/stud and any washers; replace if worn or damaged
Do-It-Yourself Stories from Customers like You
Dryer drum was making one heck of a racket while running Michael R. • Closter , NJ • January 08, 2015
The cylinder roller that supports the dryer drum was worn and needed to be replaced. I ordered the idler pulley shaft and associated parts as well since I wasn't sure if these were worn too.
Watching the video on the web site gave me a good idea what was involved and where to look. It wasn't my exact model and make but provided sufficient information on what to look for. The parts were exact fits which was a great relief abd the dryer is running like new again!
Read more
More
$3.65
- Compare At:
-
$4.46
- You Save:
-
$0.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP359364
This small retaining clip secures a lever mechanism inside the appliance, keeping the linkage aligned so the control operates smoothly. Replacing a bent or missing clip helps restore proper engagement and prevents the mechanism from popping loose. What it does:
- Locks the lever mechanism to its bracket or shaft
- Maintains alignment of moving linkage for consistent operation
- Replaces missing, bent, or broken retainer
- Common symptoms: loose/wobbly lever, mechanism slips out, control doesn't engage reliably
What's included:
Install notes:
- Disconnect power before servicing
- Access the mechanism per your model's service information and relieve any spring/linkage tension
- Note the original orientation; use needle-nose pliers to seat the new clip fully in the groove
- Test the mechanism for smooth operation before reassembly
Do-It-Yourself Stories from Customers like You
Broken retaining clip Jeff S. • Eldora , IA • May 04, 2015
Removed body to get access to leveling foot area and replaced clip
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP76314
Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A
Do-It-Yourself Stories from Customers like You
Bad fill hose. Rick D. • Maywood , NJ • January 05, 2022
Replaced hose and washers.
Read more
More
$32.43
- Compare At:
-
$38.59
- You Save:
-
$6.16