Kenmore Dryer 110.77087600 (11077087600, 110 77087600) Parts

This seal sits between the dryer's blower housing and its cover to keep the air path tight. Replacing a crushed or torn seal helps restore proper airflow and drying performance while minimizing lint leakage inside the cabinet.

• Creates an airtight joint between the blower housing and cover
• Helps prevent air leaks that lead to longer dry times
• Helps keep lint contained within the exhaust path
• Replace if the original seal is torn, flattened, deteriorated, or missing

• Disconnect power; for gas models, shut off gas and allow the dryer to cool
• Access the blower housing (typically behind the lower front panel)
• Clean mating surfaces; install the new seal evenly around the perimeter with no gaps
• Reassemble and verify strong, unobstructed airflow at the exhaust

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This precision-drilled burner orifice is sized for Type 4 butane applications. It meters gas to the burner so flames ignite reliably and burn cleanly when the appliance is configured for butane per the manufacturer's specifications. What it does:

• Regulates gas flow to the burner head for proper flame size and shape
• Type 4 drilling intended for butane gas configurations specified by the manufacturer
• Replaces a missing or stripped orifice during service or gas-type conversion

• 1 burner orifice (Type 4, butane)

• Shut off gas supply and power; allow the appliance to cool before service
• Access the orifice at the burner base/manifold; remove the original with the correct wrench or socket
• Start threads by hand; tighten snugly—avoid overtightening or cross-threading
• After reassembly, leak-check with soapy water and verify flame; gas conversions should be performed following OEM instructions and local codes

Screw for control panel.

This control knob replaces a worn or broken range/oven front knob to restore tactile control and clear temperature/setting selection. It gives a secure fit so you can safely set burners or oven functions. What it does:

• Replaces a damaged or missing control knob to restore manual control of burners or oven settings
• Provides a clear pointer for accurate selection of heat levels and functions
• Snaps on to the stove/range control shaft for reliable operation
• Helps eliminate slipping, stripped splines, or loose turning caused by a worn knob

• One control knob as shown

• Turn power and gas supply off before servicing; follow appliance safety guidance
• Pull off the old knob straight from the control shaft and push the replacement fully onto the shaft until it seats
• If knob does not fit, do not hammer or modify the shaft

This gas valve is the safety/regulator assembly that controls gas flow to burners in compatible ranges and ovens, restoring reliable ignition and stable flames for safe cooking. What it does:

• Regulates and directs gas to the oven/range burner when the control calls for heat
• Helps ensure consistent burner ignition and steady flame height
• Common symptom: burners or oven will not light or maintain a flame
• Can address intermittent ignition or loss of heat when valve sticks or fails

• Shut off gas supply and electrical power before beginning any repair
• Installation may require removing access panels and disconnecting gas and electrical connections
• Check all gas fittings for leaks after installation using a soapy-water test or approved leak detector

This finished burner funnel directs gas and air into the burner for correct flame shape and ignition. It replaces a damaged or corroded funnel to help restore even heating and reliable burner performance. What it does:

• Channels gas and air into the burner for proper mixing and flame distribution
• Helps maintain even flame across the burner for consistent cooking heat
• Can reduce ignition delays or uneven flames caused by a damaged funnel
• Works with the burner assembly; not a standalone gas valve or igniter

• Turn off gas supply and electricity to the appliance before servicing
• Replace only with the correct funnel for your burner; follow OEM diagram for orientation
• Tighten fittings by hand-first, then snug—do not overtighten; inspect for leaks after reassembly

Replacement 1/4-inch hex flange nut that secures panels, brackets and other appliance hardware. Restores a firm connection to reduce rattling and keep assemblies aligned for reliable operation. What it does:

• Fastens panels, brackets, hinges and small assemblies to maintain proper alignment.
• Prevents loose or vibrating panels that can cause noise or premature wear.
• Replaces missing, stripped or damaged nuts to restore secure mounting.
• Works where a flange provides extra bearing surface to resist loosening.

• Always unplug the appliance or disconnect power before beginning service.
• Use the correct socket or wrench size to avoid rounding the nut; hand-start threads to prevent cross-threading.
• Do not overtighten; tighten until components are seated and secure.
• Replace any damaged mating fasteners or hardware to ensure a reliable repair.

This harness clip secures appliance wiring to the cabinet or components to prevent rubbing, pinching, and interference with moving parts. It keeps wiring routed neatly for reliable operation and reduced risk of abrasion-related failures. What it does:

• Holds wire harnesses in place to prevent chafing against sharp edges or moving parts
• Reduces vibration-related noise and intermittent connections caused by loose wiring
• Helps maintain proper wire routing around panels, motors, and heaters
• Supports safe operation by keeping wires away from heat sources and pinch points

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove panels or access covers as needed to reach the original clip location
• Install by snapping or seating the clip into the original mounting point and securing the harness in the retainer; replace any broken mounts
• Inspect surrounding wiring and replace damaged wires or insulation before completing repair

This self-drilling screw secures appliance panels and components where a fastener must cut its own pilot hole. It provides a quick, reliable hold for repair or reassembly of trim, brackets, and internal fixtures. What it does:

• Fastens panels, brackets, and small components without pre-drilling
• Helps stop loose or rattling trim and parts caused by missing or worn screws
• Restores proper alignment and secure mounting after repairs
• Works where sheet metal or thin substrates require self-tapping engagement

• One self-drilling screw

• Disconnect power and follow appliance safety procedures before starting repairs
• Use the correct size driver and steady pressure to avoid stripping the head
• Start straight and apply firm, even torque; avoid overtightening which can damage mounting surfaces
• Wear eye protection and handle small fasteners carefully to avoid loss or ingestion hazards

Color: White.

This gas burner tube replaces a damaged or corroded oven burner tube to restore proper gas flow to the burner assembly. It's a direct-fit replacement that helps re-establish even heating and reliable ignition. What it does:

• Channels gas from the manifold to the oven burner for a steady flame
• Restores consistent burner flame shape and heat distribution
• Helps correct weak or uneven heating caused by a cracked or clogged tube
• Reduces gas leakage risk from damaged tubing when installed correctly

• Designed for direct replacement; refer to your model's service manual for exact removal/installation steps
• Turn off gas supply and power before starting work; verify no gas leaks after installation
• Inspect surrounding components (burner, igniter, orifices) and clean if needed for optimal performance

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.