Kenmore Washer 110.82374100 (11082374100, 110 82374100) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP367594
This front foot assembly is the adjustable leveling leg located at the front of the appliance. It supports and stabilizes the cabinet so it sits square and level, helping prevent rocking, vibration, and poor door alignment.
- Provides front support and height adjustment to level the unit
- Helps reduce rocking, vibration, and rattling during operation
- Replaces a worn, broken, missing, or stripped front foot
- Helps ensure doors or drawers align and close properly when leveled
What's included: 1 front foot assembly Install notes:
- Disconnect power and, if applicable, shut off water/gas before servicing
- Protect flooring; carefully tip or brace the appliance to access the front foot
- Unthread the old foot; thread in the new foot and adjust until level side-to-side and front-to-back
- Verify stability, then restore utilities and recheck for level
Do-It-Yourself Stories from Customers like You
Front foot was damaged Deborah L. • Mount Pleasant , WI • June 08, 2015
Replaced, it was a cinch!!!
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$19.79
- Compare At:
-
$21.36
- You Save:
-
$1.57
Genuine Whirlpool part
By: Whirlpool
Part Number: WP354255
A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:
- Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
- Reduces vibration and rattling during operation
- Helps doors and panels sit properly when closed
- Simple, non-electrical part — no wiring or adjustment required
What's included:
Install notes:
- Inspect the mounting hole or surface; clean debris before installing
- Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
- Disconnect power to the appliance first and follow OEM instructions
- Remove old adhesive before installing the new bumper
Do-It-Yourself Stories from Customers like You
Needed water pump and lid switch Joe N. • Palmdale , CA • November 16, 2019
I utilized your videos. The pump video implied if the leak was ignored? You would have to cut the pump off, which was what I did. The impeller also had to be cut down to the plastic collar on the motor shaft, which I used a handheld chop grinder to get through the plastic collar without damaging the shaft, because of the neglect on the leak the motor shaft had to be filed and sandpapered to accept the new pump. The harness clips on the lid switch were difficult to get to but I managed without...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350365
2 Port. Whirlpool and Kenmore washers.
Do-It-Yourself Stories from Customers like You
Water drain pump would not turn any more Robert T. • Belleville , IL • January 20, 2016
Ordered a replacement. Had to tip washer toward the back to provide access underneath to the
pump. Had some difficulty removing the two hose clamps. Pliers were not the best tool. Had to ensure the drive belt was properly engaged with the pulley of the pump.
Read more
More
$92.56
- Compare At:
-
$110.15
- You Save:
-
$17.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP359231
This protective cover for the washer's lid switch area guards the switch and wiring from water, detergent, and snagging inside the top panel, supporting reliable lid-closed detection and long-term safety interlock performance.
- Shields the lid switch and wiring from splashes, detergent, and debris under the top panel
- Helps prevent snagging or accidental contact with the switch mechanism
- Supports consistent lid-closed sensing by keeping the switch area protected and in position
- If the shield is damaged or missing, you may notice exposed switch/wiring or intermittent starting/spinning that improves when the lid is pressed
What's included: 1 shield Install notes:
- Disconnect power before servicing; turn off water if moving the appliance
- Access the lid switch area by raising the top or opening the console per the service procedure
- Install the shield in the original orientation and secure with the existing fasteners
- After reassembly, verify the lid closes properly and the washer starts/spins as expected
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596797
Genuine Whirlpool part
By: Whirlpool
Part Number: WP94614
For mating terminal use [AP31136300].
More
$4.95
- Compare At:
-
$5.89
- You Save:
-
$0.94
Genuine Whirlpool part
By: Whirlpool
Part Number: 358277
Made by Whirlpool. Fits most Whirlpool, Kenmore, Estate and Roper belt driven washing machines.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine would not stop dripping into basket when finished washing Howard S. • Minneapolis , MN • April 25, 2021
Replaced washer water inlet valve.
Read more
More
$93.72
- Compare At:
-
$111.53
- You Save:
-
$17.81
Genuine Whirlpool part
By: Whirlpool
Part Number: 350938
Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Dryer drum completely wore off all coating Larry W. • Ubly , MI • July 01, 2016
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do
Read more
More
$46.95
- Compare At:
-
$55.87
- You Save:
-
$8.92
Genuine Whirlpool part
By: Whirlpool
Part Number: WP358160
This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.
- Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
- Helps prevent fasteners from loosening due to vibration and thermal cycling
- Common fix for rattling/vibration noises and components that work loose over time
- Replaces damaged, rounded, or missing original nut to restore proper fit
What's included: 1 lock nut Install notes:
- Disconnect power and shut off gas/water supplies before servicing
- Remove the worn nut with the appropriate wrench or socket
- Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
- Inspect the mating bolt/stud and any washers; replace if worn or damaged
Do-It-Yourself Stories from Customers like You
Dryer drum was making one heck of a racket while running Michael R. • Closter , NJ • January 08, 2015
The cylinder roller that supports the dryer drum was worn and needed to be replaced. I ordered the idler pulley shaft and associated parts as well since I wasn't sure if these were worn too.
Watching the video on the web site gave me a good idea what was involved and where to look. It wasn't my exact model and make but provided sufficient information on what to look for. The parts were exact fits which was a great relief abd the dryer is running like new again!
Read more
More
$3.65
- Compare At:
-
$4.46
- You Save:
-
$0.81