Kenmore Washer 110.82671110 (11082671110, 110 82671110) Parts

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

This hose coupling connects a flexible appliance hose to the appliance plumbing, restoring a secure water connection and preventing leaks. Ideal when a worn or damaged coupling causes drips or loose hose fit. What it does:

• Provides a secure connection point between an appliance hose and the appliance inlet
• Replaces cracked, broken or corroded couplings that can leak or allow the hose to detach
• Restores proper hose sealing to reduce water drips at the connection
• Compatible with the original inlet connection type and mounting orientation

• Turn off and disconnect appliance power and shut off the water supply before replacing
• Remove the old coupling and clean the mating surfaces; inspect hose and clamps for wear
• Use proper clamps and hand-tighten; avoid over-tightening which can damage fittings

This agitator cap is the top cover for the washer agitator/auger assembly, keeping the agitator hardware protected and holding the auger components in place. It restores a finished appearance and ensures the agitator operates without interference. What it does:

• Covers and protects the agitator bolt and internal auger components from debris and fabric
• Helps keep the agitator secure and centered during wash cycles
• Can reduce rubbing or noise caused by a cracked, loose, or missing cap
• Supports proper fit of the agitator assembly for smooth agitation

• One agitator cap assembly

• Disconnect power to the washer before starting any repair
• Remove the agitator per the OEM instructions to access and replace the cap
• Inspect surrounding components (bolt, washer) and replace any worn parts as needed
• Use proper tools and wear gloves to avoid cuts from sharp edges

Spring-style hose clamp that secures flexible appliance hoses to fittings, helping keep connections tight to reduce leaks and maintain proper water flow. Use it to replace a worn or damaged clamp and restore a reliable hose seal. What it does:

• Compresses around a flexible hose to lock it onto barbs or fittings
• Helps prevent drips, leaks, and water pooling at hose connections
• Keeps hoses from slipping off during appliance operation
• Useful when a clamp is corroded, stretched, or no longer holds tension

• Disconnect power and shut off water to the appliance before starting any repairs
• Use pliers to compress the clamp for removal and installation; keep hands and face clear when releasing tension
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn

A decorative trim ring that restores the finished look around an appliance opening and helps protect the underlying edges from dirt and wear. Replaces a cracked, chipped or missing trim for improved appearance and fit. What it does:

• Covers and protects the exposed edge of a control opening or panel
• Restores a clean, factory appearance after damage or removal
• Helps keep dirt and moisture from collecting at the trim edge
• Stops minor rattles or movement caused by a missing or damaged trim

• Disconnect power (or unplug) before beginning any work to avoid shock
• Remove any surrounding bezels or fasteners as needed to access the trim location
• Align the trim, press or fasten into place until fully seated; use correct OEM screws/clips if required
• Replace any damaged clips or mounting hardware before final assembly

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This drain hose coupling kit connects the washer drain hose to the appliance drain outlet, restoring a secure, leak-resistant hose connection and preventing water leaks during drain cycles. What it does:

• Provides a replacement coupling to join the drain hose to the washer drain outlet
• Re-establishes a tight hose connection to reduce leaks and water damage
• Addresses symptoms such as leaking at the drain connection or a loose hose fit
• Compatible with affected Whirlpool top-load washer drain assemblies

• Unplug the appliance before servicing and work on a dry surface
• Remove the old coupling and inspect the hose and outlet for damage before installing
• Ensure the hose is fully seated and secure with the existing or supplied clamp(s)

Motor mount to gear case.

This agitate gear washer is a small flat washer used with the washer's agitate gear to ensure proper spacing and smooth engagement. It helps maintain correct gear alignment so the agitator can move laundry effectively. What it does:

• Provides a stable spacer between the agitate gear and mating components to prevent excess play
• Helps maintain correct gear alignment for consistent agitator movement
• Reduces metal-on-metal contact that can cause noise or premature wear
• Commonly replaced when the agitator feels loose, makes grinding noise, or causes uneven agitation

• High-level replacement: remove agitator/gear per service manual to access washer; reinstall in original orientation
• Use manufacturer torque/settings for reassembly; do not overtighten
• Inspect adjacent gear and splines for wear; replace any damaged components
• Disconnect power and follow safety procedures before servicing the washer

Color: White