Kenmore Washer 110.84870810 (11084870810, 110 84870810) Parts

This tub ring seal provides a watertight gasket between the inner and outer tubs to help prevent leaks and moisture buildup. Replacing a worn or damaged seal restores proper sealing and reduces visible puddling. What it does

• Seals the joint between the inner and outer washer tubs to keep water contained during cycles
• Helps stop leaks that appear at the front or bottom of the washer
• Reduces water intrusion that can cause dampness, staining, or mold build-up near the tub opening
• Restores proper fit when the original seal is cracked, torn, or flattened

• Disconnect power and shut off water supply before starting any repair
• Replacing this seal typically requires removing the outer tub/front panel; follow the appliance-specific service manual
• Inspect mating surfaces and replace any damaged clips or retaining rings as needed for a proper seal

Flexible drain hose with gooseneck that routes wastewater from the appliance to the household drain. Replaces damaged or clogged discharge tubing to restore normal draining and reduce the risk of leaks. What it does:

• Channels wastewater from the pump to the home drain via a gooseneck discharge connection.
• Restores proper draining when original discharge tubing is cracked, split, or clogged.
• Helps maintain the gooseneck high loop to reduce backflow/siphoning when installed correctly.
• Common symptoms it addresses: standing water in the tub, slow draining, or leaks at the hose connection.

• Disconnect power and water supply before starting any repair.
• Route the hose to match the original gooseneck/high-loop routing; avoid kinks and sharp bends.
• Secure both ends with appropriate hose clamps or factory clips and check for tight, leak-free connections.

This replacement nut threads onto a stud or bolt to clamp appliance parts securely. Replace a stripped, rusted, or missing nut to restore a tight, rattle-free fit.

• Clamps components together by tightening onto a matching stud or bolt
• Helps maintain alignment and resists loosening from vibration and heat cycles
• Replaces damaged, corroded, or missing hardware during service
• Symptoms include loose or rattling parts, assemblies backing off, or difficulty keeping components secured

• Disconnect power (and shut off gas, if applicable) before servicing
• Match the thread type/direction to the original; start by hand to avoid cross-threading
• Tighten snugly; follow any model-specific torque guidance and avoid overtightening
• Inspect companion bolts/studs and washers; replace any worn or damaged hardware

This replacement clamp secures flexible hoses and lines to prevent leaks and keep connections tight. It restores a secure seal so appliances move water or air without escaping at the joint. What it does:

• Secures inlet, drain or water lines to fittings and housings
• Helps stop leaks from loose or worn hose connections
• Keeps hoses from slipping off during operation or vibration
• Commonly replaced when clamps are corroded, broken, or no longer hold tension

• Inspect hose and fitting for damage before installing the new clamp
• Position clamp over the hose barb and tighten evenly until snug; avoid over-tightening
• Use appropriate tools (pliers or clamp driver) and follow appliance safety procedures
• Disconnect power and shut off water supply when working on water lines

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

This replacement caster and socket assembly restores smooth rolling and stable support for the appliance cabinet. Use it to replace a worn or damaged wheel and mounting socket so the appliance moves easily and sits level. What it does:

• Provides a rolling wheel and mounting socket to support appliance movement and weight.
• Replaces cracked, seized, or worn casters that cause dragging, sticking, or uneven motion.
• Helps reduce noise and cabinet scuffs from a damaged or loose wheel.
• Restores proper alignment when the appliance tilts or does not roll smoothly.

• Disconnect power and water and move the appliance to a safe, stable work area before starting.
• Support the appliance to prevent tipping when removing/installing the caster.
• Remove any trim or mounting hardware covering the caster; match orientation and fasteners when installing the replacement.
• After installation, verify the appliance rolls smoothly and sits level; tighten fasteners as needed.

Spring-style hose clamp that secures flexible appliance hoses to fittings, helping keep connections tight to reduce leaks and maintain proper water flow. Use it to replace a worn or damaged clamp and restore a reliable hose seal. What it does:

• Compresses around a flexible hose to lock it onto barbs or fittings
• Helps prevent drips, leaks, and water pooling at hose connections
• Keeps hoses from slipping off during appliance operation
• Useful when a clamp is corroded, stretched, or no longer holds tension

• Disconnect power and shut off water to the appliance before starting any repairs
• Use pliers to compress the clamp for removal and installation; keep hands and face clear when releasing tension
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

Bottle with brush. Color: Harvest Gold. It's 0.6 fluid ounces.

This agitate gear washer is a small flat washer used with the washer's agitate gear to ensure proper spacing and smooth engagement. It helps maintain correct gear alignment so the agitator can move laundry effectively. What it does:

• Provides a stable spacer between the agitate gear and mating components to prevent excess play
• Helps maintain correct gear alignment for consistent agitator movement
• Reduces metal-on-metal contact that can cause noise or premature wear
• Commonly replaced when the agitator feels loose, makes grinding noise, or causes uneven agitation

• High-level replacement: remove agitator/gear per service manual to access washer; reinstall in original orientation
• Use manufacturer torque/settings for reassembly; do not overtighten
• Inspect adjacent gear and splines for wear; replace any damaged components
• Disconnect power and follow safety procedures before servicing the washer