Kenmore Dryer 110.87582601 (11087582601, 110 87582601) Parts

Small replacement clip that secures panels or small internal components to restore a snug fit and reduce rattling or misalignment. Use this clip when a worn or broken retainer lets trim or parts sit loose. What it does:

• Holds trim, panels or other small appliance components in place to maintain correct alignment.
• Helps eliminate rattling, vibration noise or gaps caused by a missing or damaged clip.
• Restores secure fit where a broken clip allows parts to shift or separate.
• Simple, low-profile replacement part used in affected Whirlpool appliances.

• Disconnect power (unplug or shut off breaker) before servicing any appliance.
• Small part; keep track of screws and retainers during disassembly.
• Basic hand tools may be required; trim or panel removal might be necessary to access the clip.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This door seal is the refrigerator door gasket that helps maintain a tight seal to keep cold air in and reduce energy loss. Replacing a worn or torn gasket helps the appliance cool efficiently and protect stored food. What it does

• Forms an airtight barrier around the refrigerator door to prevent warm air from entering
• Helps maintain consistent internal temperature and efficient operation
• Reduces frost buildup and cycling caused by a leaking seal
• Commonly shows symptoms like visible cracks, tears, flattening, or a door that won't close snugly

• One refrigerator door gasket

• Inspect the door frame and strike surfaces; clean mounting channel before installing the new gasket
• Warm the gasket slightly or use recommended installation tools to ease fitting into the channel
• Check alignment and closure after installation; replace if mounting clips or retainer are damaged
• Disconnect power only if required by your model and follow all safety precautions

This replacement screw is a direct-fit fastener used to secure appliance panels, brackets and small assemblies. It restores proper attachment and helps eliminate loose or rattling parts for safer, quieter operation. What it does:

• Fastens trim, panels, brackets or internal components to maintain proper alignment
• Keeps control panels and access panels securely attached
• Helps stop rattling, vibration noise or shifting parts caused by loose fasteners
• Works wherever the OEM screw specification matches the original mounting screw

• Disconnect power and water before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening to prevent damage to threads or parts
• Inspect surrounding parts and replace any damaged clips or fittings for a secure repair

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This light socket holds the appliance bulb and provides a reliable electrical connection, restoring clear visibility inside your unit. Replace a cracked, heat-damaged, or loose socket to fix lights that flicker, go out, or won't stay seated.

• Secures the bulb and makes proper electrical contact with the wiring
• Powers the bulb when the control or door switch commands illumination
• Helps maintain consistent lighting during normal operation
• Typical symptoms: light won't turn on with a good bulb, flickers, intermittent lighting, burnt or brittle socket, bulb won't stay seated

• Disconnect power to the appliance before servicing; allow hot areas to cool
• Note wire locations and socket orientation; take a photo before removal
• Transfer any mounting screws/bracket from the old socket as needed
• Install the correct bulb type and wattage per your appliance manual; do not overtighten

Color: White

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

This housing slot heater melts ice and prevents frost buildup inside the appliance housing, helping restore normal airflow and component operation. It's a direct replacement heater element used where ice forms around the housing slot. What it does:

• Provides targeted heat to the housing slot to reduce ice accumulation
• Helps restore proper airflow and circulation by clearing frost/ice blockages
• Commonly replaced when the housing develops repeated ice buildup or intermittent heating
• Works as part of the defrost/anti-ice system to protect internal components

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing exterior panels or trim; keep fasteners organized
• Handle the heater element and wiring with care to avoid damage to the element or connector

This drum hole plug seals an unused or service access hole in the dryer drum to help prevent clothing snags and reduce interior airflow leaks. Simple replacement restores the drum surface and helps keep items from catching. What it does:

• Covers a drum access/service hole to provide a smooth interior surface
• Prevents fabric from catching or tearing on open drum holes
• Reduces unwanted air leakage through the drum
• Helps maintain normal drum rotation contact points by keeping openings closed

• One drum hole plug

• Disconnect power to the appliance before starting any repairs
• Inspect the drum area and remove any debris before installing the plug
• Press or snap the plug into the hole until fully seated; replace if damaged or deformed

Outer door glass that restores the oven door viewing window and replaces cracked, chipped, or broken glass so the door functions safely and looks like new. What it does

• Replaces damaged or shattered outer door glass to restore a clear viewing window.
• Stops rattling or loose glass caused by broken mounting points or cracks.
• Helps maintain proper door appearance and user visibility into the oven cavity.
• Useful when glass has visible chips, cracks, or safety concerns.

• One outer door glass

• Disconnect power to the appliance before beginning any repair.
• Handle glass with heavy-duty gloves and eye protection; glass can break unexpectedly.
• Replacing this part typically requires removing the oven door and disassembling panels—follow the OEM service manual or instructions.
• Inspect and replace any worn clips, screws, or seals as needed; do not overtighten fasteners.

For mating plug use 691707.