Kenmore Dryer 110.87872601 (11087872601, 110 87872601) Parts

Replacement clip that secures trim, panels, or small components to restore proper fit and reduce rattling and vibration. Install when a worn or missing clip leaves trim or panels loose or causes intermittent noise. What it does:

• Holds trim, panels or small assemblies in place to prevent movement
• Stops rattling and vibration caused by loose parts
• Replaces broken or missing clips that allow gaps or misalignment
• Small, snap-in retainer shaped to match original attachment point

• Always disconnect power before servicing the appliance
• Access the clip location by removing the adjacent panel or trim per the OEM diagram
• Clip typically snaps into place; use needle-nose pliers or a flat screwdriver to remove the old clip if needed

This exhaust pipe routes exhaust air from the appliance to the home vent, restoring proper airflow for safe, efficient operation. Use when the original pipe is cracked, bent, or leaking. What it does:

• Channels exhaust gases and lint from the appliance to the external vent
• Prevents exhaust leaks that can cause poor drying or cooking performance
• Helps maintain correct airflow to reduce overheating and moisture buildup
• Fits where a damaged or corroded exhaust connection needs replacement

• One exhaust pipe

• Disconnect power (and gas if applicable) before servicing; follow appliance safety procedures
• Inspect surrounding seals and clamps; replace clamps or ducting if damaged
• Secure pipe with OEM-recommended fasteners and ensure vent path is clear

This exhaust pipe vents hot, moist air from the dryer to the home venting system, helping the appliance dry clothes efficiently and reduce indoor humidity. Replace a damaged or restricted pipe to restore proper airflow. What it does:

• Channels dryer exhaust air safely from the appliance to the exterior vent
• Helps prevent overheating and long dry times caused by restricted airflow
• Reduces lint buildup in the appliance by providing a clear vent path
• Commonly replaced when cracked, crushed, kinked, or badly corroded

• Disconnect power to electric dryers; shut off gas supply and disconnect for gas dryers before servicing
• Inspect existing vent path for additional damage or lint buildup and clean before installing
• Position pipe without sharp bends or kinks and secure with appropriate clamps or fasteners

This is a single replacement screw used to secure appliance panels and components. It restores proper fastening to help eliminate looseness and rattling and keep parts aligned for safe operation. What it does:

• Secures trim, panels or internal components to maintain proper alignment
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or stripped screws for safe, reliable fit
• Works wherever the OEM screw specification and fit match the original

• One screw as shown

• Disconnect power and/or gas before accessing internal components
• Use the proper driver size and avoid over-tightening to prevent thread damage
• Verify correct screw placement against the appliance's service diagram

This small retaining clip secures internal trim, panels, or wiring runs to keep components in place and prevent rattles or loose connections. It restores proper fit and helps maintain safe, quiet operation. What it does:

• Holds panels, trim pieces, or wiring harnesses in position to prevent movement
• Stops rattling and wear from vibration or loose parts
• Helps maintain correct alignment of surrounding components
• Useful when replacing damaged or missing fasteners during repairs

• Disconnect power to the appliance before starting any repair
• Access may require removal of trim, panels, or other parts; retain screws and fasteners
• Clip installs by snapping into a mating hole or channel; avoid forcing to prevent breakage
• Use appropriate-size trim tools to avoid scratching surrounding surfaces

This exhaust pipe directs heated air from the dryer drum to the household vent, restoring proper airflow for efficient drying and reduced lint buildup. It's a direct-fit replacement designed to match the OEM airflow path. What it does:

• Channels dryer exhaust from the appliance to the external vent to maintain proper airflow.
• Helps prevent lint accumulation in the cabinet by providing a sealed exhaust path.
• Can reduce long dry times and overheating caused by restricted or damaged venting.
• Addresses symptoms such as poor drying performance, hot dryer cabinet, or noticeable burning/overheating smells near the dryer vent area.

• One exhaust pipe.

• Disconnect power (and gas, if applicable) before starting work; the appliance is fully de-energized.
• Wear gloves to avoid sharp edges; remove old pipe and clean vent connections before installing the replacement.
• Secure with appropriate clamps or fasteners and ensure a continuous, unobstructed path to the exterior vent.
• After installation, run a short cycle to check for leaks.

This replacement plug seals a drain or access opening to prevent leaks and keep refrigerant/condensate and debris where they belong. Fits service openings on compatible Whirlpool appliances to restore a watertight seal. What it does:

• Seals a drain, access hole, or service opening to stop water or debris from leaking out
• Helps maintain proper condensate routing and prevents pooling inside the cabinet
• Prevents pests and dust from entering through unused openings
• Simple, non-electrical part that restores the original seal and function

• One plug

• Disconnect power to the appliance before servicing; follow all safety procedures
• Press the plug firmly into the opening until fully seated; use hand pressure only unless otherwise specified
• Inspect for proper sealing and test with a small water flow before reassembling the appliance

This electronic control board is intended for use with dryers. This component is an interior part protected by other components of the dryer. The electronic control board is the part that ensures all of the other components are working correctly. It manages the parts and controls the temperature and cycle time of the dryer. The most common sign that the electronic control board has gone bad is a dryer that refuses to start. However, it can also cause the dryer to stop heating, continue a cycle endlessly, or cause start and stop behavior. To replace this part, a screwdriver and nut wrench will be required. Shut off the power before removing the top panel to access the electronic control board. Use the screwdriver to remove it so the new part can be installed. Reconnect the wires in the appropriate locations, reinstall the dryer panel, and restore power before using the appliance.Designed for use with Kenmore and Whirlpool dryers, this part is sold as a single item. It is an authentic replacement part that has been sourced directly from the manufacturer.