Kenmore Washer Dryer Combo 110.88675810 (11088675810, 110 88675810) Parts

This protective cover for the washer's lid switch area guards the switch and wiring from water, detergent, and snagging inside the top panel, supporting reliable lid-closed detection and long-term safety interlock performance.

• Shields the lid switch and wiring from splashes, detergent, and debris under the top panel
• Helps prevent snagging or accidental contact with the switch mechanism
• Supports consistent lid-closed sensing by keeping the switch area protected and in position
• If the shield is damaged or missing, you may notice exposed switch/wiring or intermittent starting/spinning that improves when the lid is pressed

• Disconnect power before servicing; turn off water if moving the appliance
• Access the lid switch area by raising the top or opening the console per the service procedure
• Install the shield in the original orientation and secure with the existing fasteners
• After reassembly, verify the lid closes properly and the washer starts/spins as expected

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

This replacement flexible hose transports water between appliance components to restore proper flow and prevent leaks. It's a direct-fit service part used when the original hose is cracked, split, or leaking. What it does

• Carries water between the pump, tub, valve or drain—depending on model configuration
• Replaces damaged or brittle hose sections that cause visible leaks or puddling
• Restores proper draining when kinks or collapses impede flow
• Helps stop intermittent drips or steady leaks that occur during operation

• One flexible replacement hose

• Disconnect power and shut off the water supply before starting work
• Inspect and replace hose clamps or connectors if corroded or damaged
• Route and secure the hose to avoid kinks, pinching, or contact with sharp edges
• Test the appliance through a full cycle after installation and check all connections for leaks

This support is a replacement mounting bracket designed to secure and stabilize internal components. Restoring a damaged support helps keep panels and assemblies aligned for quieter, more reliable appliance operation. What it does:

• Provides a secure mounting point to hold panels or components in place
• Prevents movement that can cause rattling, vibration, or misalignment
• Helps maintain proper fit and operation of adjoining parts and panels
• Typically replaces worn, bent, or broken supports that allow looseness

• Disconnect power and, if applicable, water before starting any repair
• Inspect surrounding fasteners and mating surfaces; replace any damaged clips or screws
• Use proper tools and follow the appliance service manual for access and removal

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.

• Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
• Helps prevent fasteners from loosening due to vibration and thermal cycling
• Common fix for rattling/vibration noises and components that work loose over time
• Replaces damaged, rounded, or missing original nut to restore proper fit

• Disconnect power and shut off gas/water supplies before servicing
• Remove the worn nut with the appropriate wrench or socket
• Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
• Inspect the mating bolt/stud and any washers; replace if worn or damaged

This small retaining clip secures a lever mechanism inside the appliance, keeping the linkage aligned so the control operates smoothly. Replacing a bent or missing clip helps restore proper engagement and prevents the mechanism from popping loose. What it does:

• Locks the lever mechanism to its bracket or shaft
• Maintains alignment of moving linkage for consistent operation
• Replaces missing, bent, or broken retainer
• Common symptoms: loose/wobbly lever, mechanism slips out, control doesn't engage reliably

• Clip only

• Disconnect power before servicing
• Access the mechanism per your model's service information and relieve any spring/linkage tension
• Note the original orientation; use needle-nose pliers to seat the new clip fully in the groove
• Test the mechanism for smooth operation before reassembly

This cap secures the ice-transfer auger in the dispenser, helping the auger run smoothly and keep ice moving from the bin to the chute. It's a small replacement part that restores proper auger alignment and reduces noise. What it does:

• Secures and centers the auger on the drive shaft to prevent wobble
• Helps maintain consistent ice feed during dispensing
• Prevents the auger from slipping off the motor shaft
• Can reduce scraping or grinding noise caused by a loose or damaged cap

• Disconnect power to the appliance before starting any repair
• Remove ice and access the auger assembly per your model's service instructions
• Align the cap on the auger/shaft and secure it in place; verify smooth rotation by hand before reassembly
• If the auger or shaft shows damage, replace those components as needed

This bumper cushions the contact point where a door or drawer meets the cabinet, helping reduce slamming noise and preventing metal-to-metal contact. Replacing a worn or missing bumper protects finishes and restores smooth, quiet operation. What it does:

• Cushions the closing of a door or drawer against the frame
• Helps reduce rattling, vibration, and impact noise
• Protects painted/enamel surfaces from chips and scratches
• Helps correct spacing if a bumper is missing, flattened, or hardened

• 1 bumper

• Disconnect power to the appliance before servicing
• Open the door/drawer and locate the bumper mounting point; remove the old bumper
• Clean the mounting surface to ensure proper seating
• Press-fit the new bumper into place (follow your model's instructions), then test closure and alignment

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This is a 10-16 x 1/2 inch appliance screw used to secure panels and components on compatible Whirlpool laundry and kitchen appliances. It restores a secure fit when a fastener is missing or stripped. What it does

• Fastens trim, panels, brackets or small components to the appliance chassis
• Replaces a lost or damaged factory screw to stop rattling or loose parts
• Matches OEM thread and length for proper engagement and holding strength
• Helps maintain alignment and safe operation of the attached part

• Use the correct screwdriver or nutdriver to avoid stripping the head
• Tighten until snug—do not overtighten to prevent damage to threads or sheet metal
• Disconnect power and follow the appliance manufacturer's safety instructions before servicing

This tub ring seal provides a watertight gasket between the inner and outer tubs to help prevent leaks and moisture buildup. Replacing a worn or damaged seal restores proper sealing and reduces visible puddling. What it does

• Seals the joint between the inner and outer washer tubs to keep water contained during cycles
• Helps stop leaks that appear at the front or bottom of the washer
• Reduces water intrusion that can cause dampness, staining, or mold build-up near the tub opening
• Restores proper fit when the original seal is cracked, torn, or flattened

• Disconnect power and shut off water supply before starting any repair
• Replacing this seal typically requires removing the outer tub/front panel; follow the appliance-specific service manual
• Inspect mating surfaces and replace any damaged clips or retaining rings as needed for a proper seal

This is the replacement spring used in the console lock assembly to restore proper tension and movement in the control lock mechanism. It helps the lock return to its resting position so the console control operates correctly. What it does:

• Provides tension for the console/keyboard lock mechanism so buttons and switches return properly
• Restores correct movement of the lock actuator to engage and release the console lock
• Can resolve symptoms such as a stuck or unresponsive console lock or buttons that don't spring back
• Small part that is part of the overall console lock assembly function

• One spring for the console lock assembly

• Disconnect power (unplug or trip breaker) before servicing the appliance
• Access requires removing the console or control panel—keep track of screws and orientation
• Handle carefully; small spring can be difficult to seat, consider using needle-nose pliers or a magnetic pickup tool