Kenmore Washer Dryer Combo 110.88732793 (11088732793, 110 88732793) Parts

This endcap is a direct-fit replacement housing end cap that helps protect and support adjacent components, keeping internal parts aligned and reducing wear. It restores proper fit and function where a damaged or missing endcap causes noise or misalignment. What it does

• Covers and protects the end of the housing to prevent debris entry and reduce component wear
• Helps maintain correct alignment of internal parts to minimize vibration and noise
• Replaces cracked, broken, or worn endcaps that can allow movement or rubbing
• Useful when visible damage or play is present at the housing edge

• Disconnect power (and water if applicable) before beginning any repair
• Basic disassembly of the appliance's housing or access panel is usually required; keep fasteners organized
• Inspect surrounding seals, gaskets, and mounting tabs for damage and replace if needed

This drum baffle restores the internal lift inside the dryer drum to help separate clothes and promote even tumbling. Replacing a cracked or missing baffle can reduce banging noises and help restore consistent drying performance. What it does:

• Lifts and moves clothes for more even tumbling and airflow inside the drum.
• Helps prevent garments from bunching or wrapping around the drum during a cycle.
• A damaged or missing baffle can cause loud thumping, scraping noises, or uneven drying; replacing it addresses these common symptoms.
• Designed to match the OEM drum mounting points for proper fit and function.

• Disconnect power (and gas, if applicable) before servicing the dryer.
• Access typically requires removing the dryer front or drum; keep track of fasteners and take photos for reassembly.
• Use basic hand tools and avoid forcing parts; inspect mounting hardware and drum condition while replacing the baffle.

This lid assembly replaces a damaged or discolored top lid so your washer closes properly and looks like new. It restores the washer's top cover, improving cosmetic appearance and allowing the lid switch and hinge to function correctly. What it does:

• Replaces a cracked, warped or broken top lid that won't close or latch securely
• Restores the mounting surface for the lid switch and hinge so the washer can operate safely
• Improves the washer's appearance when the original lid is chipped, scratched, or yellowed
• Helps prevent dirt and debris from entering the tub area

• One lid assembly

• Disconnect power to the washer before starting any repair to avoid shock or injury
• Remove any screws or hinge pins securing the old lid; keep track of fasteners and springs
• Lift the old lid off the hinges and set the new lid into place, reinstalling hardware securely
• If the lid switch or hinge hardware is damaged, replace those parts separately.

This leveling link assembly connects and stabilizes the appliance's leveling system so the unit sits square and the door closes properly. It prevents uneven operation and helps stop rocking or tipping during use. What it does:

• Links the cabinet to the leveling leg so height adjustments transfer correctly
• Restores stable, even positioning to reduce rocking and misalignment
• Helps ensure the door seals and latches properly by keeping the appliance level
• Commonly replaced when links are broken, bent or separated from the leg/box

• One leveling link assembly

• Disconnect power to the appliance before servicing
• Support the appliance so it cannot tip when removing or installing the link
• Verify leveling leg height and alignment after installation; adjust legs as needed

This is a replacement power cord that restores electrical connection between your appliance and the household outlet, letting the appliance receive mains power safely. It replaces a damaged or worn cord to help restore normal operation. What it does:

• Carries mains voltage from the wall outlet to the appliance so it can power up and operate
• Replaces frayed, melted, or broken cords that can cause intermittent power or no power at all
• Helps eliminate arcing or loose connection symptoms that may trip breakers or cause burning smells
• Restores a secure, strain-relieved connection when the original cord or terminal is damaged

• One replacement power cord

• Always disconnect power at the breaker or unplug the appliance before replacing the cord
• Route the cord and secure the strain relief or clamp per the appliance's wiring access panel

This outer refrigerator door replaces a damaged or worn exterior door panel so your fridge seals and looks like new. It restores proper closure and helps maintain internal temperature control and appliance appearance. What it does:

• Replaces a damaged, dented or cracked outer refrigerator door panel
• Restores a straight, secure door edge for better sealing and operation
• Helps prevent cold air loss that can cause temperature fluctuations
• Improves appliance appearance by replacing scratched or faded exterior finish

• One outer refrigerator door panel

• Disconnect power and empty the door before starting; remove any screws or hinge covers securing the door
• Lift or support the door while removing hinge fasteners to avoid dropping or damaging the cabinet
• Align hinges and test door swing and seal before tightening all fasteners
• If inner components (bins, trim, gaskets) are attached, they should be properly reinstalled or transferred per manufacturer instructions.

Kit includes 2 sleeves.

This replacement button bar restores the row of pushbuttons on the control panel so you can operate your appliance's functions easily. It replaces cracked, worn, or missing button strips and helps return normal button feel. What it does:

• Provides the pushbutton interface that actuates the control switches behind the panel
• Aligns and secures into the control console so each button depresses cleanly
• Common symptoms it fixes: broken, loose, missing, or sticky buttons and intermittent button response
• Matches factory fit and mounting points for a straightforward panel replacement

• Disconnect power (unplug or shut off breaker) before starting any repair
• Typically installed from the front or back of the control console after removing the console or trim
• Handle plastic tabs gently to avoid breaking mounting clips during removal/installation