Kenmore Washer Dryer Combo 110.88752798 (11088752798, 110 88752798) Parts

This drum baffle restores the internal lift inside the dryer drum to help separate clothes and promote even tumbling. Replacing a cracked or missing baffle can reduce banging noises and help restore consistent drying performance. What it does:

• Lifts and moves clothes for more even tumbling and airflow inside the drum.
• Helps prevent garments from bunching or wrapping around the drum during a cycle.
• A damaged or missing baffle can cause loud thumping, scraping noises, or uneven drying; replacing it addresses these common symptoms.
• Designed to match the OEM drum mounting points for proper fit and function.

• Disconnect power (and gas, if applicable) before servicing the dryer.
• Access typically requires removing the dryer front or drum; keep track of fasteners and take photos for reassembly.
• Use basic hand tools and avoid forcing parts; inspect mounting hardware and drum condition while replacing the baffle.

This wire harness assembly routes power and signals between controls and components to restore electrical connection and appliance function. It replaces a damaged or worn harness to help recover intermittent or lost circuits. What it does:

• Carries power and control signals between console, motor, sensors and other appliance components
• Restores connectivity when wires are frayed, pinched or connectors are corroded
• Can stop intermittent operation, no-power conditions, or absent control responses caused by harness faults
• Maintains factory routing and connector fit for reliable electrical contact

• Disconnect power (unplug appliance or turn off breaker) before inspecting or replacing the harness
• Compare connector shapes and wire colors to ensure correct replacement before installing
• Route harness along original clips and channels; avoid sharp edges, heat sources and pinch points
• Secure connectors firmly; if terminals or connectors are damaged, replace them rather than reusing compromised parts

This leveling link assembly connects and stabilizes the appliance's leveling system so the unit sits square and the door closes properly. It prevents uneven operation and helps stop rocking or tipping during use. What it does:

• Links the cabinet to the leveling leg so height adjustments transfer correctly
• Restores stable, even positioning to reduce rocking and misalignment
• Helps ensure the door seals and latches properly by keeping the appliance level
• Commonly replaced when links are broken, bent or separated from the leg/box

• One leveling link assembly

• Disconnect power to the appliance before servicing
• Support the appliance so it cannot tip when removing or installing the link
• Verify leveling leg height and alignment after installation; adjust legs as needed

This outer refrigerator door replaces a damaged or worn exterior door panel so your fridge seals and looks like new. It restores proper closure and helps maintain internal temperature control and appliance appearance. What it does:

• Replaces a damaged, dented or cracked outer refrigerator door panel
• Restores a straight, secure door edge for better sealing and operation
• Helps prevent cold air loss that can cause temperature fluctuations
• Improves appliance appearance by replacing scratched or faded exterior finish

• One outer refrigerator door panel

• Disconnect power and empty the door before starting; remove any screws or hinge covers securing the door
• Lift or support the door while removing hinge fasteners to avoid dropping or damaging the cabinet
• Align hinges and test door swing and seal before tightening all fasteners
• If inner components (bins, trim, gaskets) are attached, they should be properly reinstalled or transferred per manufacturer instructions.

Kit includes 2 sleeves.

This console clip secures the appliance control console or control panel to the cabinet, restoring a snug, stable fit and stopping rattles or loose movement. Durable plastic clip designed to replace a broken or worn fastener. What it does:

• Holds the control console in place to prevent sagging or separation from the cabinet
• Stops rattling or vibration noise caused by a loose console
• Restores proper alignment for buttons and switches on the control panel
• Replaces a cracked, worn, or missing mounting clip

• One console mounting clip (1 each)

• Disconnect power before attempting any service to avoid shock or injury
• Remove the console or access panel per your model's service instructions to reach the clip
• Pry out the damaged clip carefully and snap the new clip into the factory mounting boss until it seats
• Handle plastic parts gently to avoid cracking; before reassembling

This wiring assembly replaces a worn or damaged wire harness to restore electrical connections between an appliance's controls and components. It helps re-establish reliable power and signal routing for proper appliance operation. What it does:

• Routes power and signal connections between control modules, switches, sensors and major components
• Restores interrupted circuits that can cause controls to be unresponsive or the appliance to fail to start
• Replaces cracked, frayed or heat-damaged wiring that may cause intermittent operation or arcing
• Ensures proper connector fit and factory routing to prevent shorts and electrical faults

• Disconnect power at the breaker or unplug the appliance before starting any work
• Compare the new harness to the old one and follow original wire routing and connector orientation
• Secure harness with existing clips or fasteners; avoid contact with moving parts or hot surfaces

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it