Kenmore Washer Dryer Combo 110.88764793 (11088764793, 110 88764793) Parts

Spring-style hose clamp that secures flexible appliance hoses to fittings, helping keep connections tight to reduce leaks and maintain proper water flow. Use it to replace a worn or damaged clamp and restore a reliable hose seal. What it does:

• Compresses around a flexible hose to lock it onto barbs or fittings
• Helps prevent drips, leaks, and water pooling at hose connections
• Keeps hoses from slipping off during appliance operation
• Useful when a clamp is corroded, stretched, or no longer holds tension

• Disconnect power and shut off water to the appliance before starting any repairs
• Use pliers to compress the clamp for removal and installation; keep hands and face clear when releasing tension
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This blower housing directs dryer airflow from the drum to the exhaust for proper ventilation and consistent drying performance. It replaces a cracked or damaged housing to restore airflow and reduce noise. What it does:

• Channels heated air from the drum to the exhaust vent to maintain drying efficiency
• Helps support the blower wheel and keeps the wheel aligned for smooth operation
• Commonly replaced for reduced airflow, longer dry times, or unusual noise from the rear of the dryer
• Can prevent overheating caused by restricted or leaking airflow

• Disconnect power (and gas supply if applicable) before beginning repair
• Handle edges carefully; wear gloves to avoid cuts and protect the blower wheel
• Reassemble panels and test dryer on a short cycle to confirm airflow and quiet operation

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This drain hose coupling kit connects the washer drain hose to the appliance drain outlet, restoring a secure, leak-resistant hose connection and preventing water leaks during drain cycles. What it does:

• Provides a replacement coupling to join the drain hose to the washer drain outlet
• Re-establishes a tight hose connection to reduce leaks and water damage
• Addresses symptoms such as leaking at the drain connection or a loose hose fit
• Compatible with affected Whirlpool top-load washer drain assemblies

• Unplug the appliance before servicing and work on a dry surface
• Remove the old coupling and inspect the hose and outlet for damage before installing
• Ensure the hose is fully seated and secure with the existing or supplied clamp(s)

This drum hole plug seals an unused or service access hole in the dryer drum to help prevent clothing snags and reduce interior airflow leaks. Simple replacement restores the drum surface and helps keep items from catching. What it does:

• Covers a drum access/service hole to provide a smooth interior surface
• Prevents fabric from catching or tearing on open drum holes
• Reduces unwanted air leakage through the drum
• Helps maintain normal drum rotation contact points by keeping openings closed

• One drum hole plug

• Disconnect power to the appliance before starting any repairs
• Inspect the drum area and remove any debris before installing the plug
• Press or snap the plug into the hole until fully seated; replace if damaged or deformed

This OEM replacement part is a washer tub assembly. The tub is the cylindrical piece that is found inside the washer where the clothes are put. Damage to the tub can cause it to not rotate properly. If the tub is making excessive noise during the wash cycle and appears to be misaligned, damaged, or broken, it might be time for a replacement. Start by removing the front panel of the washing machine. Then proceed to remove the top and back panels. After gaining access to the interior of the machine, disconnect any hoses attached to the drum and take note of where they go. Using a screwdriver, remove the screws that hold the drum to the machine. Lift the tub out, and replace it with the new one. Be sure to re-attach everything properly. Secure the front back and top panels of the washer.This genuine replacement part is compatible with Bosch, Gaggenau, and Thermador, washing machines.

Motor mount to gear case.

This hex nut secures fasteners on compatible Whirlpool appliances to keep panels and components held firmly in place. It's a simple replacement that stops loose parts and restores proper fit and function. What it does:

• Threads onto corresponding bolts or studs to lock panels, brackets, or assemblies.
• Stops vibration-related loosening that can cause rattling or misaligned parts.
• Helps re-secure components after service or collision damage.
• Use when the original nut is stripped, missing, or damaged.

• Disconnect power and unplug the appliance before servicing electrical components.
• Use the correct size socket or wrench to avoid rounding the nut.
• Tighten securely but do not overtighten; replace with matching thread and grade if specified by the OEM.
• If the original fastener was seized or damaged, inspect the mating bolt/stud and replace as needed.