Kenmore Washer Dryer Combo 110.98573800 (11098573800, 110 98573800) Parts

A cam sleeve that supports and guides the cam on its shaft to keep the cam-driven mechanism moving smoothly. Replacing a worn sleeve helps restore correct alignment and reduces binding or intermittent movement. What it does

• Centers and stabilizes the cam on its shaft for reliable engagement.
• Prevents metal-on-metal wear between the cam and shaft.
• Helps eliminate binding, wobble, or uneven operation caused by a worn sleeve.
• Common symptom of failure: noise, sticking, or irregular movement from the cam-driven mechanism.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing the appropriate service panel; follow the model service manual.
• Inspect mating cam and shaft for wear; replace any damaged components.
• Reassemble panels and verify proper operation before returning the appliance to service.

This lid latch secures the appliance lid and, on interlock-equipped models, signals that the lid is closed so the cycle can run safely. It restores proper closure and dependable operation when the original latch is worn or broken. What it does

• Latches the lid closed to prevent unintended opening during operation
• Engages the lid switch/lock circuit where used, allowing the cycle to start or continue
• Helps maintain alignment between the lid and strike/keeper for reliable closure
• Common symptoms include: lid won't stay closed, unit won't start or advance, intermittent stopping when the lid is bumped

• 1 lid latch

• Disconnect power before servicing; turn off water supply if applicable
• Access the latch, remove retaining screws/clips, and note orientation for reassembly
• Install the new latch and align it with the lid strike/keeper; reuse original hardware if required
• Close the lid and run a short test to ensure proper engagement and operation

This exhaust vent extension provides extra duct length to move dryer or hood exhaust farther from the appliance, improving airflow routing and helping reduce backpressure and lint buildup in short-vent installations. What it does:

• Extends the length of an existing exhaust duct to reach a distant vent outlet
• Helps restore proper ventilation when original ducting is too short
• Reduces restricted airflow that can cause longer dry times or excess lint accumulation
• Works as an inline rigid/semirigid extension piece for exhaust systems

• Disconnect power (and gas for gas dryers) before accessing or modifying exhaust connections
• Remove lint and debris from ducting before installing the extension to ensure clear airflow
• Securely fasten with appropriate clamps or foil tape and maintain a smooth, unobstructed path

This drain tube funnels and directs excess water away from the appliance to the drain path, helping prevent pooling and water damage. It replaces a worn, cracked or clogged tube to restore proper water flow. What it does:

• Carries water from the appliance's drainage area to the drain outlet
• Helps prevent leaks and interior water buildup from a damaged or disconnected tube
• Can resolve symptoms like water pooling under/behind the appliance or intermittent draining
• Ensures proper routing so water flows to the drain instead of into the cabinet

• One drain tube

• Disconnect power to the appliance before starting any repair
• Turn off water supply and remove any panels needed to access the tube
• Inspect and replace any worn clamps or fasteners; ensure tube is routed without kinks
• After installation, restore power/water and run a test cycle to ensure there are no leaks

Use with motor 357282.

This terminal block access cover protects the appliance's electrical connection area, helping keep wires shielded and reducing the risk of accidental contact. It restores the factory appearance and helps maintain safe operation. What it does:

• Shields the terminal block and wiring from dust, debris, and accidental contact
• Helps prevent shorting or arcing at the power connection area
• Restores a finished look after service or replacement of wiring components
• Supports safe access control by covering live terminals when installed

• Disconnect power at the breaker or unplug the appliance before servicing.
• Remove or loosen the mounting fasteners for the old cover, then position and secure the replacement cover.
• Verify the cover fits flush and does not pinch wiring; ensure all connections are tight before restoring power.

Motor mount to gear case.

This block restraint is a small mounting block that secures internal components and limits movement to reduce noise and wear. It restores proper alignment and keeps parts from shifting during operation. What it does:

• Anchors and stabilizes nearby components to prevent excessive movement and vibration
• Helps reduce rattling or banging noises caused by loose internal parts
• Keeps parts aligned to prevent premature wear or abrasion
• Supports safe, reliable operation by holding components in the intended position

• One block restraint

• Disconnect power (and water for washers/dishwashers) before beginning any repair
• Access the mounting location by removing the appropriate panel(s); basic hand tools typically required
• Remove the old block and replace with the new restraint; ensure correct orientation and secure fit
• Inspect surrounding fasteners and mounting surfaces; do not overtighten plastic parts

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This ignition electrode delivers the spark needed to light the burner in compatible gas ovens and ranges, restoring reliable ignition so burners and bake/broil functions light properly. What it does:

• Produces the spark for the gas burner to ignite
• Helps ensure consistent ignition timing and burner starts
• Commonly used when a burner fails to light or ignition is intermittent
• Works with the oven/range ignition system to start bake and broil cycles

• Disconnect power and shut off the gas supply before starting any repair
• Handle the ceramic/insulated tip carefully to avoid cracking or contamination
• Verify correct electrode position and secure mounting for reliable sparking

This cove transition panel is the black trim piece that restores the look and fit between your cooktop and control area. It provides a finished appearance and replaces a cracked, bent, or missing transition trim. What it does:

• Covers the gap between the cooktop and control/cabinet area for a clean, finished appearance
• Replaces damaged, cracked, or warped trim that can affect panel alignment
• Helps maintain correct spacing and fit of adjacent trim pieces
• Restores original factory appearance after collision or wear

• Disconnect power to the appliance before starting any work
• Handle edges carefully to avoid cuts and prevent scratching the finish
• Minor disassembly of surrounding trim or panels may be required; keep fasteners organized