Kenmore Freezer 253.44733103 (25344733103, 253 44733103) Parts

This adhesive-backed plastic mounting clip secures wires, small hoses, or components inside appliances to reduce movement and rattling. Its low-profile design helps keep internal parts organized for quieter, safer operation. What it does:

• Holds wiring harnesses, sensor leads, or small tubing in place to prevent chafing and noise
• Reduces vibration-related contact that can cause intermittent electrical or sensor issues
• Provides a simple, non-invasive mounting point without drilling or fasteners
• Adhesive backing allows quick placement in tight or hard-to-reach areas

• Clean and dry mounting surface; remove backing and press clip firmly for full adhesion
• Allow adhesive to set per ambient temperature (avoid stress on clip during initial cure)
• Disconnect power before installing
• Replace any brittle or damaged surrounding insulation or wire loom as needed

This electronic controller is the central board that governs your unit's cooling system. It processes temperature inputs and controls key components so the freezer maintains set temperature when the original board fails.

• Regulates temperature by processing sensor/thermostat inputs and issuing commands to cooling components
• Directs compressor and fan operation to maintain the setpoint
• On applicable models, manages defrost timing and cycles
• Common failure symptoms include no cooling or intermittent cooling, unit won't start, runs constantly, unresponsive controls, or erratic temperatures

• Disconnect power before service; observe ESD precautions and handle the board by its edges
• Photograph/label wire connections; transfer any mounting clips/brackets from the original board
• Seat all connectors fully without forcing; avoid touching component pins
• Restore power and allow time for temperatures to stabilize; verify normal operation

This Icemaker assembly replaces the refrigerator freezer icemaker to restore automatic ice production and delivery to the ice bin. It installs where the original icemaker mounts and reconnects to the existing water supply and wiring. What it does:

• Cycles through fill, freeze and harvest stages to form ice cubes and drop them into the bin
• Receives water from the inlet and meters fill volume to produce properly sized cubes
• Stops producing ice when the bin is full to prevent overflow or ice buildup
• Resolves common symptoms like no ice production, few or misshapen cubes, or an icemaker that won't cycle

• One icemaker assembly

• Disconnect power and water supply before starting any work
• Handle the ice bin and harness carefully; use basic hand tools for removal and reinstallation
• Follow model-specific service manual or OEM instructions for wiring and alignment
• After installation, restore power/water and run a test cycle to ensure proper operation

A small metal clamp that secures the refrigerator's capillary (temperature sensing) tube to the cold control so the thermostat reads temperatures accurately. Replaces worn or missing clamps to keep the sensing tube stable and prevent movement-related issues. What it does:

• Holds the capillary/sensing tube firmly against the cold control or cabinet
• Helps maintain accurate thermostat sensing by preventing tube movement
• Reduces vibration or rattling from a loose sensing tube
• Stops intermittent temperature swings caused by a displaced capillary tube

• Disconnect power before servicing the appliance.
• Handle the capillary tube gently; avoid kinks or sharp bends.
• Install clamp over the tube and secure to the control or bracket using the factory hole or fastener; do not overtighten.

This mounting bracket secures internal components and panels to restore proper alignment and reduce vibration. It provides a direct replacement for worn or damaged support hardware so assemblies stay firmly in place. What it does:

• Secures appliance panels or internal components to the cabinet or frame
• Keeps parts aligned to prevent rattling, vibration, or movement during operation
• Restores proper fit where a bent, broken, or missing bracket causes loose assemblies
• Helps maintain safe, stable operation by holding parts in their designed position

• One mounting bracket

• Designed to replace the factory bracket in the same mounting location; verify fit before installation
• Use appropriate fasteners and torque to avoid striping or damage to mounting points
• Disconnect power and empty unit if needed before accessing internal areas

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

Note: For clips only, order part# 297049500.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation