Kenmore Freezer 253.44772702 (25344772702, 253 44772702) Parts

This Icemaker assembly replaces the refrigerator freezer icemaker to restore automatic ice production and delivery to the ice bin. It installs where the original icemaker mounts and reconnects to the existing water supply and wiring. What it does:

• Cycles through fill, freeze and harvest stages to form ice cubes and drop them into the bin
• Receives water from the inlet and meters fill volume to produce properly sized cubes
• Stops producing ice when the bin is full to prevent overflow or ice buildup
• Resolves common symptoms like no ice production, few or misshapen cubes, or an icemaker that won't cycle

• One icemaker assembly

• Disconnect power and water supply before starting any work
• Handle the ice bin and harness carefully; use basic hand tools for removal and reinstallation
• Follow model-specific service manual or OEM instructions for wiring and alignment
• After installation, restore power/water and run a test cycle to ensure proper operation

A small metal clamp that secures the refrigerator's capillary (temperature sensing) tube to the cold control so the thermostat reads temperatures accurately. Replaces worn or missing clamps to keep the sensing tube stable and prevent movement-related issues. What it does:

• Holds the capillary/sensing tube firmly against the cold control or cabinet
• Helps maintain accurate thermostat sensing by preventing tube movement
• Reduces vibration or rattling from a loose sensing tube
• Stops intermittent temperature swings caused by a displaced capillary tube

• Disconnect power before servicing the appliance.
• Handle the capillary tube gently; avoid kinks or sharp bends.
• Install clamp over the tube and secure to the control or bracket using the factory hole or fastener; do not overtighten.

This mounting bracket secures internal components and panels to restore proper alignment and reduce vibration. It provides a direct replacement for worn or damaged support hardware so assemblies stay firmly in place. What it does:

• Secures appliance panels or internal components to the cabinet or frame
• Keeps parts aligned to prevent rattling, vibration, or movement during operation
• Restores proper fit where a bent, broken, or missing bracket causes loose assemblies
• Helps maintain safe, stable operation by holding parts in their designed position

• One mounting bracket

• Designed to replace the factory bracket in the same mounting location; verify fit before installation
• Use appropriate fasteners and torque to avoid striping or damage to mounting points
• Disconnect power and empty unit if needed before accessing internal areas

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

This is a replacement screw used to secure appliance components and panels. It provides a reliable fastener for repairs and maintenance, restoring secure attachment where the original screw is missing or damaged. What it does:

• Secures trim, panels, brackets, or small components to prevent rattling and movement
• Restores proper fit where a worn or stripped screw caused loose parts
• Helps eliminate noise caused by loose hardware
• Use as a direct replacement when the original screw is lost or damaged

• Use the matching driver bit and moderate torque to avoid stripping the head or threads
• Replace like-for-like: confirm length and thread type before installation
• Disconnect power and remove stored items from the appliance area before accessing internal panels
• If screws pull out of plastic or metal repeatedly, check for damaged threads or underlying mounting issues

This replacement screw fastens appliance panels and components to restore a secure fit and reduce vibration or rattling. Use when original hardware is missing, loose, or stripped to keep parts aligned and operating quietly. What it does:

• Secures panels, brackets, and trim to prevent movement and rattling.
• Replaces missing or damaged hardware that can cause loose or misaligned parts.
• Helps maintain proper component alignment for reliable operation.
• Small but essential fastener for safe, stable assembly.

• Disconnect power before servicing any electrical appliance.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten, which can strip threads or crack panels.
• Keep removed hardware organized to ensure correct reinstallation.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

This door hinge replaces a worn or damaged refrigerator door pivot to restore proper door alignment and sealing. It helps stop sagging, uneven gaps, and doors that stick or don't close fully. What it does

• Provides a stable pivot point so the refrigerator door opens and closes smoothly.
• Restores proper door alignment to improve the magnetic seal and reduce cold air loss.
• Reduces binding, scraping, and rattling associated with worn hinge points.
• Helps correct a door that droops, drags on the cabinet, or sits unevenly.

• One replacement door hinge.

• Unplug the appliance or disconnect power before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Use basic hand tools; tighten fasteners securely but do not overtighten.
• Refer to OEM instructions for exact hinge location and torque specs.

This replacement cover is an access panel trim piece that protects internal components and gives the appliance a finished appearance. It restores a secure, clean-looking exterior where the original cover is cracked or missing. What it does

• Covers and protects control or component openings from dust, debris, and accidental contact
• Keeps wiring and fasteners concealed for a neater appearance
• Prevents rattling or vibration caused by a damaged or loose trim piece
• Commonly replaced when the cover is cracked, broken, warped, or missing

• One cover

• Disconnect power to the appliance before starting any work
• Remove adjacent trim or fasteners as needed to access mounting points; retain hardware for reassembly
• Align tabs or screw holes and secure without over-tightening to avoid cracking the plastic

Water inlet tube routes incoming water from the refrigerator's supply line to the dispenser and ice maker, restoring proper water flow and helping stop leaks when a cracked or damaged inlet tube is the problem. What it does:

• Directs incoming water to the ice maker and dispenser; a damaged tube can cause weak or no water flow and reduced ice production.
• Cracks, splits, kinks or loose connections commonly produce visible leaks under or behind the refrigerator.
• Replacing the inlet tube restores reliable water delivery and helps prevent continued water damage from a compromised line.
• Inspect nearby fittings and clamps during replacement — loose or corroded fittings are a common related cause of leaks.

• Turn off the water supply and disconnect power before starting — uncontrolled water or live electrical parts create safety hazards.
• Relieve residual water pressure and catch any drips; have towels or a shallow pan ready.
• Replace any damaged clamps, seals, or fittings and tighten connections to factory torque; inspect surrounding tubing for additional damage.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary