Kenmore Refrigerator 253.60734407 (25360734407, 253 60734407) Parts

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly

This foam insulation block helps fill gaps and reduce heat transfer inside the refrigerator cabinet to maintain proper cooling and reduce frost/condensation. It restores the designed insulation barrier where the original piece is damaged or missing. What it does:

• Replaces a damaged or missing foam block that seals internal gaps in the cabinet or behind panels
• Helps prevent warm air infiltration that can cause poor cooling or excess frost
• Reduces condensation and moisture buildup around the evaporator area or panel seams
• Supports consistent temperature performance by restoring insulation continuity

• One foam insulation block

• Disconnect power to the appliance before beginning any repair
• Access location may require removing interior panels or shelves; handle panels and clips carefully
• Install in the exact position and orientation of the original part; use any existing adhesive or fasteners as required
• If adhesive is needed, use only appliance-safe adhesives compatible with foam and follow manufacturer guidance

This door stop is the replacement limiter that keeps an appliance door from over-rotating, protecting hinges and cabinet edges. It restores consistent door travel and helps the door close smoothly and securely. What it does:

• Limits how far the door opens to prevent hinge or cabinet damage
• Helps the door close in the correct position and reduces slamming
• Fits into the door/hinge assembly to provide a stable stop point
• Common symptom: door opens too far, bangs against surrounding cabinetry, or hang/align issues

• High-level replacement — remove door/hinge trim as needed per your model's instructions
• Use basic hand tools; keep fasteners separate and note orientation for reassembly
• Disconnect power if working near electrical components (applies to ovens/microwaves)

This access cover is a replacement access panel that protects internal components and closes service openings for safe, finished appliance operation. It restores a secure, clean appearance and prevents debris from entering service areas. What it does:

• Covers and protects internal components behind service openings
• Keeps wiring and connections enclosed and out of reach
• Prevents dirt, lint, and small objects from entering service areas
• Restores a finished look and secures loose or missing panels
• Helps reduce drafts through service openings

• Disconnect power (unplug or shut off breaker) before installing
• Use basic hand tools; align tabs or screw holes before fastening
• Handle edges carefully to avoid cuts and prevent damage to surrounding trim

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

Made of Nylon with adhesive tape

This is a complete refrigerator door assembly that replaces a damaged or worn exterior door to restore sealing, appearance, and proper closing. It ships ready to install and includes the door panel and attached components. What it does:

• Replaces a cracked, dented, or bent door to restore proper closure and insulation
• Restores cosmetic appearance and matches original fit and finish
• Ensures door seals and liner align to reduce cold-air loss and maintain temperature
• Resolves issues with the door not latching or closing smoothly

• Requires basic appliance disassembly; disconnect power and empty door before starting
• May require transfer or reuse of existing hinge hardware, gasket, or trim
• Support the door during removal/installation to avoid injury or damage