Kenmore Refrigerator 253.61792106 (25361792106, 253 61792106) Parts

This control box wiring harness routes power and signals between the appliance control board and other components to restore reliable control operation and electrical connectivity. It helps resolve intermittent controls and lost function caused by damaged wiring. What it does:

• Connects the control board to switches, sensors and motors to enable normal control functions.
• Replaces damaged or frayed wiring that can cause intermittent operation or unresponsive controls.
• Addresses symptoms such as control panel not responding, random shutdowns, or error codes tied to wiring faults.
• Restores proper signal and power routing when connector damage or wire breaks interrupt circuits.

• Disconnect all power to the appliance before beginning any service.
• Compare the new harness to the original and follow factory connector positions and routing to avoid pin miswiring or chafing.
• Handle connectors gently and ensure all terminals fully seat; inspect mating connectors for damage before reconnecting.

This cabinet corner trim is a direct-replacement trim piece that restores a finished edge and protects the appliance cabinet corner from chips, dings, and moisture. It improves appearance and keeps the cabinet edge sealed. What it does:

• Covers and protects the exposed cabinet corner to prevent further chipping or damage
• Restores a clean, finished look where the original corner trim is cracked, broken, or missing
• Helps reduce gaps that can collect dirt or moisture along the cabinet edge
• Fits into the cabinet trim profile to hold adjacent trim pieces in place when intact

• Disconnect power to the appliance before starting work if trim removal requires access behind panels.
• Remove the damaged trim carefully — some styles snap off, others are secured with clips or screws; keep hardware if reusable.
• Align the replacement trim with the cabinet edge and press or fasten into place until seated; avoid forcing plastic to prevent cracking.

This replacement rear compressor base roller supports the refrigerator compressor on the cabinet rear base, helping keep the compressor properly seated and reducing wear from vibration and movement. What it does

• Provides a rolling support under the compressor to keep it aligned and off the cabinet floor
• Helps reduce vibration and rattling that can occur from a loose or worn compressor mount
• Prevents compressor body from dragging or scraping the cabinet base
• Commonly replaced when the roller is cracked, worn flat, missing, or causing noise

• Disconnect power to the appliance before starting any work
• Support or secure the compressor and cabinet before removing the old roller to avoid sudden movement
• Basic hand tools usually required; inspect mounting hardware and replace any damaged fasteners
• Do not attempt sealed-system repairs.

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear where wiring, rods or panels pass through mounting openings. It helps keep parts aligned and protects against chafing and noise. What it does:

• Cushions and isolates vibration between moving parts and chassis
• Protects wiring, tubes or rods from rubbing and abrasion at mounting holes
• Helps reduce noise caused by contact or metal-on-metal vibration
• Aids in maintaining proper part alignment and secure fit

• Grommet

• Inspect mating hole and surrounding area for debris or sharp edges before installing
• Fit the grommet into the mounting hole so the flange seats evenly on both sides
• Replace any damaged or excessively worn grommets to restore protection
• Disconnect power and follow appliance safety procedures before attempting service

This replacement egg tray restores organized egg storage in your refrigerator door or shelf area so eggs stay upright and easy to access. Durable molded plastic replaces cracked or missing trays to help keep eggs contained. What it does:

• Holds and secures eggs to prevent rolling and tipping
• Restores a missing or damaged egg storage area in the fridge
• Helps reduce mess from cracked or loose eggs
• Fits into the refrigerator door or designated shelf location

• Simply remove the old tray and snap the new tray into the existing mounting location
• No tools required for most installations; handle gently to avoid cracking the tray
• Clean with mild detergent before first use
• Keep away from high-heat sources and avoid harsh chemicals

This rubber compressor mounting grommet cushions and isolates the compressor to reduce vibration and noise that can transfer to the cabinet. It helps maintain stable compressor positioning for quieter, smoother operation. What it does:

• Absorbs compressor vibration to lower noise and rattling
• Dampens movement that can cause abrasion or wear on mounting hardware
• Helps maintain proper alignment of the compressor assembly
• Common symptom: excessive buzzing, vibration, or rattling from the back of the appliance

• Always disconnect power to the appliance before servicing.
• Support the compressor before removing mounts to prevent shifting or damage.
• Inspect surrounding mounts and hardware; replace any worn or damaged pieces.

Color: Black. Rubber. Holds tube/wire

This condenser tube spacer positions and secures the refrigerator's condenser tubing to maintain proper tube spacing and airflow. Replacing a worn or broken spacer helps reduce vibration, rattling, and rubbing that can damage tubing over time. What it does:

• Holds condenser tubing in the correct position to preserve airflow and cooling efficiency
• Cushions tubing to limit vibration and reduce rattling noises
• Prevents tubing from rubbing against the cabinet or other components, lowering wear risk
• Helps reduce the chance of tubing fatigue that can lead to damage

• Disconnect power to the appliance before accessing rear panels or condenser components.
• Handle condenser tubing gently; avoid kinking, bending, or putting stress on lines during installation.
• Installation may require removing the back or lower access panel to reach the condenser assembly.

This genuine replacement screw secures panels and small components on select appliances, restoring fit and reducing rattles or loose parts. It's a direct-fit fastener where the original #8-18 x 3/8 screw is missing or worn. What it does:

• Fastens trim, panels or brackets to appliance frames and components
• Restores secure fit to stop rattling or misaligned parts
• Replaces stripped, rusted or missing screws that prevent proper assembly
• Matches original thread size and length for correct engagement

• Use the correct driver and engage threads straight to avoid stripping
• Do not overtighten; stop when the part is snug and secure
• Replace any damaged mating hardware for best fit
• Unplug the appliance or shut off power when accessing internal fasteners

This genuine replacement part is an evaporator used in refrigerators. The evaporator is the part that exchanges heat to cool the refrigerator. It is the component of the refrigerator that absorbs the heat from the air inside, turning it cool through absorption. If the refrigerator is no longer cooling properly, this could mean it's time for a new evaporator.This is a genuine replacement evaporator compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

This seal fits around the air diffuser to maintain a tight barrier and help direct airflow inside the appliance. It prevents air leaks and helps maintain even temperatures for better performance and efficiency. What it does:

• Creates a snug seal at the diffuser to reduce air bypass and uneven cooling
• Helps prevent excess moisture and frost buildup near the diffuser area
• Reduces drafts or weak airflow that can cause temperature inconsistency
• Helps minimize buzzing or vibration caused by loose diffuser fit

• Disconnect power to the appliance before beginning any work
• Remove the diffuser or access panel per your model's service instructions to reach the seal
• Press the seal into the diffuser channel, ensuring a full, even fit without gaps
• If the seal is brittle or torn, replace it to restore proper airflow control

Color: Black/natural. Nylon

This drain tube routes defrost and condensation water from the freezer compartment to the drain pan so moisture drains away cleanly and prevents pooling. Replaces a cracked, clogged or disconnected drain line. What it does:

• Channels defrost and condensation water out of the freezer to the drain system
• Prevents water pooling inside the freezer or refrigerator compartment
• Helps avoid leaks onto the floor when the original tube is cracked, pinched or disconnected
• Works with the appliance's drain trough and drain pan to maintain normal defrost drainage

• One drain tube

• Disconnect power before servicing and work with a cooled appliance to avoid burns
• Access may require removing interior panels or kickplate; handle panels and clips carefully
• Inspect and clear any debris or ice from the drain trough before installing the new tube
• Ensure the tube is routed without sharp bends or kinks and is securely seated at both ends

This heat exchanger suction line kit replaces a damaged or corroded suction line assembly to restore proper refrigerant flow and heat transfer in the cooling system. It helps maintain consistent compartment temperatures and system efficiency. What it does:

• Transfers heat from the refrigerant suction line so the compressor and evaporator operate correctly
• Replaces cracked, kinked, or corroded tubing that can cause refrigerant loss or reduced cooling
• Helps address symptoms such as warm or inconsistent temperatures, visible oil or residue at fittings, or abnormal frost/ice patterns
• Restores a sealed refrigerant path after tubing damage or when corrosion has compromised the line

• Intended for qualified service technicians only; system access requires certified refrigerant handling
• Disconnect power to the appliance before servicing and follow all safety precautions
• Installation may require brazing, flare fittings, or specialty tools; verify leak-tight connections and pressure-test per OEM procedures
• Evacuate and recharge the refrigerant system to OEM specifications after installation