Kenmore Refrigerator 253.68832790 (25368832790, 253 68832790) Parts

This meat pan is the removable storage tray that fits inside the refrigerator cabinet to keep raw or prepared meats contained and organized. It helps reduce leaks and makes cleaning easier. What it does:

• Collects and contains meat juices and small spills to protect other refrigerator surfaces
• Provides a dedicated, easy-to-clean surface for storing raw or prepared meat
• Keeps food organized and helps prevent cross-contamination when used properly
• Stable tray design that slides into cabinet support rails or rests on shelves

• One meat pan

• Remove power to the appliance and empty surrounding shelves before installing
• Slide the pan into the cabinet supports or place on the shelf until it sits flat
• Clean with mild detergent and warm water before first use and after each use
• Do not use abrasive cleaners or sharp tools that could damage the pan

This defrost heater melts frost and ice on the evaporator so your refrigerator can maintain proper airflow and cooling. It's the heating element used during the appliance's automatic defrost cycle. What it does

• Warms the evaporator coil to remove frost and ice buildup
• Restores normal airflow through the evaporator for consistent cooling
• Helps stop frost-related symptoms like reduced cooling or ice-covered coils
• Works as part of the defrost system along with the thermostat and control timer/board

• One defrost heater

• Disconnect power to the appliance before servicing to avoid shock
• Handle the heater carefully; avoid bending or damaging the element
• Inspect and, if necessary, test the defrost thermostat/bi-metal and wiring when replacing the heater

This glass crisper cover provides a stable shelf over the refrigerator crisper drawer, helping protect produce and contain spills while keeping the drawer accessible. Restores a level surface and improves storage organization. What it does:

• Serves as the top surface above the crisper drawer so items can be stored or rolled off safely into the drawer below.
• Helps contain spills and prevents food from falling directly into the crisper compartment.
• Replaces cracked, chipped or missing glass that can cause instability or sharp edges.
• Restores proper spacing and support for items stored on the lower refrigerator shelf area.

• One glass crisper cover.

• Disconnect power to the appliance or ensure the fridge door is open and interior lights are not a hazard before you begin.
• Handle glass with care and use gloves to avoid cuts; inspect packaging for breakage before installation.
• Align the cover with the shelf supports or locating tabs and lower gently into place until it seats securely.
• If any support rails or clips are damaged, replace them before installing the new cover for a secure fit.

A small replacement push-cap that restores the look and function of a control or panel button. Use this plug button when a worn, torn, or missing cap makes controls hard to press or exposes the switch. What it does

• Covers and protects the underlying switch or actuator from dirt and moisture
• Restores a tactile surface for reliable button presses
• Improves appearance when the original cap is cracked, torn, or missing
• Prevents accidental contact with the switch mechanism

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the control panel or trim per your model's service instructions to access the button area
• Press the plug onto the switch stem until fully seated; do not force or pry with metal tools
• If the switch underneath is damaged, replace the switch assembly rather than relying on the cap alone

This cabinet corner trim restores the finished edge where two cabinet panels meet, covering exposed corners and improving the appliance's appearance. It's a direct-replacement trim piece that helps keep panels aligned and protected from chips. What it does

• Covers and protects exposed cabinet corners from chips, dings and wear
• Hides gaps where cabinet panels meet for a neater appearance
• Helps secure and align adjacent cabinet or console panels
• Useful when original trim is cracked, broken, bent or missing

• Remove any adjacent panels or screws that block access before installing the trim
• Align trim with cabinet edge and press or fasten per the original attachment method
• Use only the OEM replacement part to ensure proper fit; do not force or bend the trim
• Disconnect power before removing panels