Kenmore Refrigerator 253.69943702 (25369943702, 253 69943702) Parts

This plug seals an unused hole in an appliance cabinet or inner liner to help block drafts, pests and moisture. It restores a clean, finished appearance and prevents accidental debris entry where a fitting or fastener is not used. What it does:

• Seals unused openings in the appliance cabinet or liner to keep out dust, moisture and pests
• Helps prevent air leaks that can affect temperature stability in refrigerators and freezers
• Covers exposed holes left after removing or relocating components or fasteners
• Restores a finished look to access areas and reduces risk of small-item ingress

• One cabinet sealing plug

• Push the plug into the hole until fully seated; no special tools usually required
• Turn off and unplug the appliance before reaching into compartments or behind panels
• Inspect the hole and plug for correct fit; replace if cracked or deformed

This genuine replacement part is an evaporator used in refrigerators. The evaporator is the part that exchanges heat to cool the refrigerator. It is the component of the refrigerator that absorbs the heat from the air inside, turning it cool through absorption. If the refrigerator is no longer cooling properly, this could mean it's time for a new evaporator.This is a genuine replacement evaporator compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

A small replacement plug button that restores the tactile control on compatible Frigidaire appliances. Replaces a cracked, worn or missing push-button so controls operate and look complete again. What it does:

• Acts as the user-facing push surface for a specific control or plug feature
• Restores normal button feel and engagement when the original is broken or missing
• Helps prevent debris from entering the switch or control opening
• Improves appearance of a damaged or worn control panel area

• Power off and unplug the appliance before starting any repair
• Usually installs by snapping into the control panel from the front; no special tools required
• Install gently to avoid damaging the surrounding bezel or switch

This replacement mounting screw secures components and panels in refrigerators and freezers, restoring proper fit and stopping loose or rattling parts. Use when original screws are missing, stripped, or damaged. What it does:

• Fastens trim, panels, brackets or small components to the appliance frame
• Restores secure attachment to stop rattling or intermittent contact
• Replaces stripped, corroded, or missing screws to prevent parts from shifting
• Simple, direct replacement that matches the original mounting point

• Use the matching driver bit to avoid stripping the screw head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power to affected appliance areas before servicing if panels expose wiring
• If threads are damaged, replace the mating nut or tapped insert as needed

Color: Black/natural. Nylon

This drain tube routes defrost and condensation water from the freezer compartment to the drain pan so moisture drains away cleanly and prevents pooling. Replaces a cracked, clogged or disconnected drain line. What it does:

• Channels defrost and condensation water out of the freezer to the drain system
• Prevents water pooling inside the freezer or refrigerator compartment
• Helps avoid leaks onto the floor when the original tube is cracked, pinched or disconnected
• Works with the appliance's drain trough and drain pan to maintain normal defrost drainage

• One drain tube

• Disconnect power before servicing and work with a cooled appliance to avoid burns
• Access may require removing interior panels or kickplate; handle panels and clips carefully
• Inspect and clear any debris or ice from the drain trough before installing the new tube
• Ensure the tube is routed without sharp bends or kinks and is securely seated at both ends

This heat exchanger suction line kit replaces a damaged or corroded suction line assembly to restore proper refrigerant flow and heat transfer in the cooling system. It helps maintain consistent compartment temperatures and system efficiency. What it does:

• Transfers heat from the refrigerant suction line so the compressor and evaporator operate correctly
• Replaces cracked, kinked, or corroded tubing that can cause refrigerant loss or reduced cooling
• Helps address symptoms such as warm or inconsistent temperatures, visible oil or residue at fittings, or abnormal frost/ice patterns
• Restores a sealed refrigerant path after tubing damage or when corrosion has compromised the line

• Intended for qualified service technicians only; system access requires certified refrigerant handling
• Disconnect power to the appliance before servicing and follow all safety precautions
• Installation may require brazing, flare fittings, or specialty tools; verify leak-tight connections and pressure-test per OEM procedures
• Evacuate and recharge the refrigerant system to OEM specifications after installation

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw