Kenmore Refrigerator 253.72242200 (25372242200, 253 72242200) Parts

This shelf spacer is a genuine OEM replacement part sourced directly from the manufacturer, and it is used in refrigerators and freezers. This shelf spacer attaches to wire shelves in the refrigerator and freezer to hold them in place. If the shelf spacer is lost or damaged, the shelf will not stay in place. The spacer should be replaced.Refrigerator shelves must be sturdy to hold the weight of the food stored inside. If the shelf spacer is missing, the stability of the shelf is compromised. This part snaps onto the wire shelf and prevents it from moving around. This keeps the food inside the refrigerator from causing the shelf to fall. No tools are needed to install this part. If the shelf spacer is missing, do not store food on the shelf until it is installed.This shelf spacer is a white plastic part that is sold individually. It is designed for use in refrigerators manufactured by Kenmore, Frigidaire, Westinghouse, and Gibson.

This defrost heater kit heats the evaporator to melt frost and ice buildup so the refrigerator can cycle normally and maintain proper cooling. It's a direct-replacement kit for units that use a heater-style defrost assembly. What it does:

• Warms the evaporator coil during the defrost cycle to remove frost and ice
• Helps restore normal airflow and cooling when frost buildup blocks the evaporator
• Commonly used when a refrigerator has excessive frost, poor cooling, or no active defrost
• Works with the existing defrost control and thermostat to allow automatic defrost cycles

• Disconnect power to the appliance before starting any service
• Handle evaporator fins and sharp sheet metal with care; wear gloves and eye protection
• Reassemble panels and restore power; check for proper defrost operation after installation

This Spill-Safe glass shelf replaces a damaged or missing refrigerator shelf and helps contain spills with raised front and rear edges to keep liquids from dripping onto lower compartments. Durable tempered glass provides a stable surface for food storage. What it does:

• Replaces cracked, chipped, or missing refrigerator shelf glass
• Raised spill-safe lip helps contain spills and prevents runoff to lower shelves
• Provides a flat, sturdy surface for storing food containers and small appliances
• Restores proper shelf spacing and organization inside the fresh-food compartment

• Remove all items from the shelf before installation; lift straight out and slide new shelf into existing supports
• Handle glass carefully and wear cut-resistant gloves to avoid injury
• Ensure shelf is seated fully on both side supports before loading
• Do not use if shelf is cracked or damaged; replace immediately

This genuine replacement screw secures panels and small components on select appliances, restoring fit and reducing rattles or loose parts. It's a direct-fit fastener where the original #8-18 x 3/8 screw is missing or worn. What it does:

• Fastens trim, panels or brackets to appliance frames and components
• Restores secure fit to stop rattling or misaligned parts
• Replaces stripped, rusted or missing screws that prevent proper assembly
• Matches original thread size and length for correct engagement

• Use the correct driver and engage threads straight to avoid stripping
• Do not overtighten; stop when the part is snug and secure
• Replace any damaged mating hardware for best fit
• Unplug the appliance or shut off power when accessing internal fasteners

This genuine replacement part is an evaporator used in refrigerators. The evaporator is the part that exchanges heat to cool the refrigerator. It is the component of the refrigerator that absorbs the heat from the air inside, turning it cool through absorption. If the refrigerator is no longer cooling properly, this could mean it's time for a new evaporator.This is a genuine replacement evaporator compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

This seal fits around the air diffuser to maintain a tight barrier and help direct airflow inside the appliance. It prevents air leaks and helps maintain even temperatures for better performance and efficiency. What it does:

• Creates a snug seal at the diffuser to reduce air bypass and uneven cooling
• Helps prevent excess moisture and frost buildup near the diffuser area
• Reduces drafts or weak airflow that can cause temperature inconsistency
• Helps minimize buzzing or vibration caused by loose diffuser fit

• Disconnect power to the appliance before beginning any work
• Remove the diffuser or access panel per your model's service instructions to reach the seal
• Press the seal into the diffuser channel, ensuring a full, even fit without gaps
• If the seal is brittle or torn, replace it to restore proper airflow control

Color: Black/natural. Nylon

This drain tube routes defrost and condensation water from the freezer compartment to the drain pan so moisture drains away cleanly and prevents pooling. Replaces a cracked, clogged or disconnected drain line. What it does:

• Channels defrost and condensation water out of the freezer to the drain system
• Prevents water pooling inside the freezer or refrigerator compartment
• Helps avoid leaks onto the floor when the original tube is cracked, pinched or disconnected
• Works with the appliance's drain trough and drain pan to maintain normal defrost drainage

• One drain tube

• Disconnect power before servicing and work with a cooled appliance to avoid burns
• Access may require removing interior panels or kickplate; handle panels and clips carefully
• Inspect and clear any debris or ice from the drain trough before installing the new tube
• Ensure the tube is routed without sharp bends or kinks and is securely seated at both ends

This temperature control thermostat regulates refrigerator cooling by cycling the compressor and fans to maintain set temperatures. Replaces a faulty thermostat to restore proper temperature control and more consistent cooling. What it does

• Senses cabinet temperature and closes or opens the electrical circuit to run the compressor and cooling system
• Helps maintain steady temperatures so food stays properly chilled or frozen
• Commonly replaces a thermostat that causes the unit to run constantly, not run at all, or fail to reach set temperatures
• Works with the fridge's control assembly to respond to user temperature adjustments

• One temperature control thermostat

• Disconnect power to the appliance before starting any repair
• Locate the thermostat behind the control knob or panel; refer to your model's service manual for exact access
• Handle the capillary tube and sensor bulb carefully to avoid kinks or damage

A replacement compressor kit designed to restore the refrigeration system's ability to cool by replacing failed compressor components. Use this kit when the compressor assembly needs service or replacement. What it does:

• Replaces failed compressor components to help restore normal cooling performance
• Stops intermittent or complete loss of cooling often caused by compressor failure
• Helps address loud humming, grinding, or continuous running tied to compressor problems
• Supports proper refrigerant flow when installed and serviced

• Disconnect power and unplug the appliance before beginning any repairs
• Compressor and sealed-system service (evacuation, vacuum, refrigerant charging) must be performed
• Use proper handling and tools for refrigerant-containing components to avoid leaks and injury